SB-230/ 8873 tube change

[W. Kranitz]

Just a note here.

There are 2 common types of Heat Sink Compound. Z5 kinda looks
like Clear Silicone rubber, while Z9 is bright white. The
characteristics are slightly different, so you should always use
the same type.

Wes
WA4AME

Steve Harrison wrote:
>
> At 11:26 PM 1/30/99 -0500, Leisman wrote:
> >Dear all:
> >
> >When I change the 8873 tube in my SB-230, I am assuming I will need to
> >clean the existing beryllium block free from the heat conductive gel,
> >re-apply the gel or cream as I replace the tube.  Anyone know where I
> >get the gel/ cream?, and, has anyone had any experience changing the
> >8873?  What did you use to clean the beryllium block and what
> >precautions did you take.
>
> It's just ordinary silicone power transistor grease; get a tube at your
> local Radio Shack. As for cleaning off the old stuff, use isopropyl alcohol
> (if available; leaves little or no residue) and paper towel, napkins, rags,
> whatever. The beryllia block is completely non-toxic and inert unless you
> file, grind or otherwise do something to cause dust particles; so don't
> sand it!! Don't scrub it, merely wipe the old gunk off. It would be a good
> idea to handle it as little as possible, naturally. If you're concerned,
> use dishwashing or vinyl medical gloves from your local drug store. I would
> deposit the dirty rags and gloves in a sealable plastic freezer bag before
> disposal. There isn't supposed to be any hazard with handling solid
> beryllia blocks like that; and many of us have handled ceramic tubes with
> abandon, not realizing that the base ceramic sometimes is beryllium oxide
> (not in between the screen ring and the base or anode cylinder, but the
> "ceramic" wafer holding the base pins itself).
>
> Now, DISPOSAL of a broken block would be a different story since it's much
> easier for chips and small particles to break off the broken edges.
>
> By the way, I've heard that the silicone heat-transfer grease is really
> more akin to the stuff that you spread over your baby's bottom so long ago.
> It's messy, but apparently non-toxic when used as intended (at least, I've
> never seen any hazardous warning). Use alcohol to wash it out of your
> hands. Then wash your hands thoroughly with soap and water and a disposable
> towel.
>
> >Any help would be appreciated.  Ican't believe I'm the only one to run
> >into the problem.
>
> Remember that hundreds of two-way-radio techs have changed 8560AS Eimac
> conduction-cooled tubes in commercial shops, which are also attached to
> beryllia insulator blocks. So while there is hazard, it's minimal unless
> you grind, crush or sand the beryllia block.
>
> 73, Steve Ko0U/1
>
> --- --- --- --- --- --- --- --- --- --- --- --- --- --
> To subscribe: listserv at listserv.tempe.gov
> and in body: subscribe HEATH yourfirstname yourlastname
> To unsubscribe:  listserv at listserv.tempe.gov
> and in body: signoff HEATH
> Archives for HEATH: http://www.tempe.gov/archives
> --- --- --- --- --- --- --- --- --- --- --- --- --- --

--- --- --- --- --- --- --- --- --- --- --- --- --- --
To subscribe: listserv at listserv.tempe.gov
and in body: subscribe HEATH yourfirstname yourlastname
To unsubscribe:  listserv at listserv.tempe.gov
and in body: signoff HEATH
Archives for HEATH: http://www.tempe.gov/archives
--- --- --- --- --- --- --- --- --- --- --- --- --- --