<!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.0 Transitional//EN">
<HTML><HEAD>
<META content="text/html; charset=windows-1252" http-equiv=Content-Type><!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.0 Transitional//EN">
<META content="MSHTML 5.00.2919.6307" name=GENERATOR>
<STYLE></STYLE>
</HEAD>
<BODY bgColor=#ffffff>
<DIV><FONT size=2>
<DIV><FONT size=2>Assuming the wiring is correct, no open plate
resistors</FONT></DIV>
<DIV><FONT size=2>Get out a scope (or spend hours with the manual
measurements)</FONT></DIV>
<DIV><FONT size=2>Check all oscillators, and plate voltages</FONT></DIV>
<DIV> </DIV>
<DIV><FONT size=2>I would start with the mixer injection points.</FONT></DIV>
<DIV> </DIV>
<DIV><FONT size=2>1-Start with the VFO first 6EA8 1st mixer injection point at
V-5 pin 7</FONT></DIV>
<DIV><FONT size=2>2-Check heterodyne oscillator injection point V6 pin
2</FONT></DIV>
<DIV>3- Carrier osc (BFO function on receive) is V 13 pin 9 (Product
detector)</DIV>
<DIV> </DIV>
<DIV><FONT size=2>I use a long tip probe on to the sockets (remove Shield) from
top of radio </FONT></DIV>
<DIV><FONT size=2>It a start </FONT></DIV>
<DIV><FONT size=2>Regards Joe</FONT></DIV></FONT></DIV>
<BLOCKQUOTE
style="BORDER-LEFT: #000000 2px solid; MARGIN-LEFT: 5px; MARGIN-RIGHT: 0px; PADDING-LEFT: 5px">
<DIV><FONT face=Arial size=2><B>-----Original Message-----</B><BR><B>From:
</B>Jerry Kitterman <<A
href="mailto:jerry@OTHERSIDE.COM">jerry@OTHERSIDE.COM</A>><BR><B>To: </B><A
href="mailto:HEATH@LISTSERV.TEMPE.GOV">HEATH@LISTSERV.TEMPE.GOV</A> <<A
href="mailto:HEATH@LISTSERV.TEMPE.GOV">HEATH@LISTSERV.TEMPE.GOV</A>><BR><B>Date:
</B>Tuesday, January 11, 2000 11:25 PM<BR><B>Subject: </B>Help
w/HW-101<BR><BR></DIV></FONT>
<DIV><FONT face=Arial>Gang,</FONT></DIV>
<DIV> </DIV>
<DIV><FONT face=Arial>Just acquired an HW-101 today with problems. It
has audio output but no signals present. Output does not vary on any
band nor does it change (peak) with the preselector. Also, no rf output
that I could see but I just tried it on one band (relay did
work).</FONT></DIV>
<DIV> </DIV>
<DIV><FONT face=Arial>The troubleshooting chart in the manual is so broad that
I just thought perhaps someone on the list might just know what to look for
first before really getting into it. TIA very much.</FONT></DIV>
<DIV> </DIV>
<DIV><FONT face=Arial>73</FONT></DIV>
<DIV><FONT face=Arial>Jerry</FONT></DIV>
<DIV><FONT
face=Arial>W9CTB
I have checked the tubes in this rig and all appear ok by my
checker.</FONT></DIV></BLOCKQUOTE></BODY></HTML>