<html><head></head><body><div style="color:#000; background-color:#fff; font-family:Helvetica Neue, Helvetica, Arial, Lucida Grande, sans-serif;font-size:16px"><div id="yui_3_16_0_ym19_1_1526434170180_6577"><span id="yui_3_16_0_ym19_1_1526434170180_6578">With the DX-35, DX-40, and DX-60- series, since those transmitters use controlled carrier modulation, if you do not modulate the transmitter, you can tune the amplifier to around 100-watts output, maybe a little more, and then the peak output is not going to exceed the capabilities of the amplifier when modulation is applied.</span></div><div id="yui_3_16_0_ym19_1_1526434170180_6576"><span><br></span></div><div id="yui_3_16_0_ym19_1_1526434170180_6568"><span id="yui_3_16_0_ym19_1_1526434170180_6567">Controlled carrier is not exactly like SSB. However, the peak output from the amplifier is going to be well within the maximum capabilities of the amplifier and the plate dissipation will definitely not be in excess of the ratings of the 572B final amplifier tubes.</span></div><div></div><div id="yui_3_16_0_ym19_1_1526434170180_6569"> </div><div class="signature" id="yui_3_16_0_ym19_1_1526434170180_6575">Glen, K9STH </div><div class="signature" id="yui_3_16_0_ym19_1_1526434170180_6575"><br></div><div class="signature" id="yui_3_16_0_ym19_1_1526434170180_6575">Website: http://k9sth.net</div><div class="qtdSeparateBR" id="yui_3_16_0_ym19_1_1526434170180_6570"><br><br></div><div class="yahoo_quoted" id="yui_3_16_0_ym19_1_1526434170180_6574" style="display: block;"> <div style="font-family: Helvetica Neue, Helvetica, Arial, Lucida Grande, sans-serif; font-size: 16px;" id="yui_3_16_0_ym19_1_1526434170180_6573"> <div style="font-family: HelveticaNeue, Helvetica Neue, Helvetica, Arial, Lucida Grande, sans-serif; font-size: 16px;" id="yui_3_16_0_ym19_1_1526434170180_6572"> <div dir="ltr" id="yui_3_16_0_ym19_1_1526434170180_6571"> <font size="2" face="Arial" id="yui_3_16_0_ym19_1_1526434170180_6603"> <hr size="1" id="yui_3_16_0_ym19_1_1526434170180_6602"> <b><span style="font-weight:bold;">From:</span></b> RAY FRIESS <rayfrijr@msn.com><br> <b><span style="font-weight: bold;">To:</span></b> Kenneth G. Gordon <kgordon2006@frontier.com>; Bill <hony53@aol.com> <br><b><span style="font-weight: bold;">Cc:</span></b> "Heath@puck.nether.net" <Heath@puck.nether.net><br> <b><span style="font-weight: bold;">Sent:</span></b> Tuesday, May 15, 2018 6:42 PM<br> <b><span style="font-weight: bold;">Subject:</span></b> Re: [Heath] DX40<br> </font> </div> <div class="y_msg_container"><br><div id="yiv2191406994">
<style><!--#yiv2191406994 .yiv2191406994EmailQuote {margin-left:1pt;padding-left:4pt;border-left:#800000 2px solid;}--></style>
<div>
<div style="margin-bottom:45px;">
<div style="font-size:10pt;">
<div>I would be interested in tune up procedure for the SB 200 in AM mode.</div>
<div><br>
</div>
<div id="yiv2191406994x_LGEmailSignatureBox">
<div><i>Sent from my Verizon LG Smartphone</i></div>
</div>
</div>
<div style="font-size:10pt;">
<div><br>
</div>
<div>------ Original message------</div>
<div><b>From: </b>Kenneth G. Gordon</div>
<div><b>Date: </b>Tue, May 15, 2018 3:02 PM</div>
<div><b>To: </b>Bill;</div>
<div><b>Cc: </b>Heath@puck.nether.net;</div>
<div><b>Subject:</b>Re: [Heath] DX40</div>
<div><br>
</div>
</div>
</div>
<font size="2"><span style="font-size:11pt;">
<div class="yiv2191406994PlainText">On 15 May 2018 at 1:18, Bill wrote:<br>
<br>
> Hi Mike and Ken.<br>
> <br>
> Yes, I will be replacing the 6146, but should I get a 6146 OR a 6146A?<br>
<br>
Doesn't matter. Any of the 6146 family will work fine in the DX-40. Even the 8298, and 6293
<br>
(if you can find one) are quite suitable. The DX-40 is not picky as far as final amp tubes are
<br>
concerned as some of the later rigs are. You should avoid the 12.6 V filamented versions,
<br>
though, unless you change the filament voltage (!)<br>
<br>
> I have a copy of the original schematic and the build manual. They both show a 0.1uf cap.
<br>
> Physically it is across from the 2 power supply electrolytic. However, on the DX 40 I acquired that
<br>
> capacitor has been replaced with a 30uf cap.<br>
<br>
Hmmmm....I am still at a loss as to where this is. Your description doesn't help me much.<br>
<br>
On my schematics, I find only one 0.1 uFd 600 V capacitor, labeled C-3, which is in the
<br>
modulator circuit. One end is connected to the junction of three 470 K resistors, and the
<br>
other end goes to ground. If that one was replaced by a 30 uFd capacitor, I would think that
<br>
it would, essentially, badly effect the audio coming from the 12AX7 speech amp by severely
<br>
reducing "lows". I suspect that who ever changed it, had some hum in the transmitted audio
<br>
and thought that by increasing that capacitor to 30 uFd, the hum would be reduced.<br>
<br>
If that was my rig, I'd change that back to 0.1 uFd 600 V.<br>
<br>
Usually, hum in the audio is caused by poor shielding of the mic cables.<br>
<br>
In any case, that capacitor is not going to effect the transmitter when in CW so unless you
<br>
intend to use the DX-40 on AM, you can safely ignore it.<br>
<br>
BTW, such controlled-carrier AM rigs as the DX-40 make excellent drivers for a <br>
grounded-grid linear amp for AM, such as the SB-200 or SB-220.<br>
<br>
Ken W7EKB<br>
<br>
---<br>
This email has been checked for viruses by Avast antivirus software.<br>
<a rel="nofollow" target="_blank" href="https://www.avast.com/antivirus">https://www.avast.com/antivirus</a><br>
<br>
_______________________________________________<br>
Heath mailing list<br>
Heath@puck.nether.net<br>
<a rel="nofollow" target="_blank" href="https://puck.nether.net/mailman/listinfo/heath">https://puck.nether.net/mailman/listinfo/heath</a><br>
</div>
</span></font>
</div>
</div>_______________________________________________<br>Heath mailing list<br><a ymailto="mailto:Heath@puck.nether.net" href="mailto:Heath@puck.nether.net">Heath@puck.nether.net</a><br><a href="https://puck.nether.net/mailman/listinfo/heath" target="_blank">https://puck.nether.net/mailman/listinfo/heath</a><br><br><br></div> </div> </div> </div></div></body></html>