[j-nsp] Implementing Ethernet Aggregated Features

[NAIDOO Kesva FTLD/IAP]

The FXP interface is only for out of band management on Juniper routers. You
cannot run any  dynamic routing protocols on these interfaces as well. Only
allowed static routes.

Kesva



-----Original Message-----
From: juniper-nsp-bounces at puck.nether.net
[mailto:juniper-nsp-bounces at puck.nether.net]On Behalf Of Paul Goyette
Sent: Thursday, April 03, 2003 1:30 PM
To: Robert Viau; Harshit Kumar; hhadiwinoto at hotpop.com;
juniper-nsp at puck.nether.net
Subject: RE: [j-nsp] Implementing Ethernet Aggregated Features


It is normal.  Aggregating the management Ethernet interface is not
supported.

-----Original Message-----
From: juniper-nsp-bounces at puck.nether.net
[mailto:juniper-nsp-bounces at puck.nether.net]On Behalf Of Robert Viau
Sent: Thursday, April 03, 2003 10:23 AM
To: Harshit Kumar; hhadiwinoto at hotpop.com; juniper-nsp at puck.nether.net
Subject: Re: [j-nsp] Implementing Ethernet Aggregated Features


Is it normal to not be able to do this with fxp interfaces?

I tried following the instructions at the link below, but the fxp interfaces
do not appear to support 'fastether-options'.  It would be nice to use an AE
interface for management as it would then provide layer 1 failover.

Thanks,

Rob

----- Original Message -----
From: "Harshit Kumar" <harshit at juniper.net>
To: <hhadiwinoto at hotpop.com>; <juniper-nsp at puck.nether.net>;
<juniper at groupstudy.com>
Sent: Friday, March 21, 2003 3:09 PM
Subject: RE: [j-nsp] Implementing Ethernet Aggregated Features


> Hope this link helps ....
>
> http://www.juniper.net/techpubs/software/junos/junos56/swconfig56-interf
> aces/html/interfaces-ethernet-config34.html#1014780
>
> --harshit
>
> -----Original Message-----
> From: hhadiwinoto at hotpop.com [mailto:hhadiwinoto at hotpop.com]
> Sent: Thursday, March 20, 2003 9:04 PM
> To: juniper-nsp at puck.nether.net; juniper at groupstudy.com
> Subject: [j-nsp] Implementing Ethernet Aggregated Features
>
>
> Hi,
>
>
> I have some questions regarding to ethernet aggregated features
> (802.3ad)
> on M-series,
> 1. Do I need to invest a special PIC for implementing fast ethernet
> aggregated features on M-series ?
> 2. can Juniper implementation for 802.3ad do load balances traffic
> (unicast
> traffic) and redudancy/fail-over (unicast traffic) as well ?
>
>
> -----------                 ------------
> |   M5    |                 |    M5    |
> -----------                 ------------
>   |  | FE        |  |  FE
>   |  |                         |  |
> -------------      FE      -------------
> | switch    | -------------|  switch   |
> -------------              -------------
>   |  FE
>   |
> -------------
> |   M5      |
> -------------
>
> any helps would be apreciated.
>
> thanks & regards
> hendro
>
>
> --------------------------------------------------------------------
> mail2web - Check your email from the web at
> http://mail2web.com/ .
>
>
>
> _______________________________________________
> juniper-nsp mailing list juniper-nsp at puck.nether.net
> http://puck.nether.net/mailman/listinfo/juniper-nsp
>
> _______________________________________________
> juniper-nsp mailing list juniper-nsp at puck.nether.net
> http://puck.nether.net/mailman/listinfo/juniper-nsp

_______________________________________________
juniper-nsp mailing list juniper-nsp at puck.nether.net
http://puck.nether.net/mailman/listinfo/juniper-nsp

_______________________________________________
juniper-nsp mailing list juniper-nsp at puck.nether.net
http://puck.nether.net/mailman/listinfo/juniper-nsp