[j-nsp] Juniper 10GE XFP

[Jay Hanke]

Does it also work on a non uplink module ie EX 4200-24F?

-----Original Message-----
From: juniper-nsp-bounces at puck.nether.net
[mailto:juniper-nsp-bounces at puck.nether.net] On Behalf Of Chuck Anderson
Sent: Tuesday, December 15, 2009 4:41 PM
To: juniper-nsp at puck.nether.net
Subject: Re: [j-nsp] Juniper 10GE XFP

On Mon, Dec 14, 2009 at 03:53:16PM -0600, Jay Hanke wrote:
> The EX is a different animal, I think there is only support for DOM 
> on the XFP ports unlike the MX where it is supported on all the SFP 
> and XFP ports. Also, I think DOM support is recent (10.0?) on the 
> EX.

No, DOM works on SFP on EX4200 with 10.0.

ex4200> show interfaces diagnostics optics ge-0/1/0 
Physical interface: ge-0/1/0
    Laser bias current                        :  23.140 mA
    Laser output power                        :  0.2170 mW / -6.64 dBm
    Module temperature                        :  47 degrees C / 117 degrees
F
    Module voltage                            :  3.2470 V
    Receiver signal average optical power     :  0.0006 mW / -32.22 dBm
    Laser bias current high alarm             :  Off
    Laser bias current low alarm              :  Off
    Laser bias current high warning           :  Off
    Laser bias current low warning            :  Off
    Laser output power high alarm             :  Off
    Laser output power low alarm              :  Off
    Laser output power high warning           :  Off
    Laser output power low warning            :  Off
    Module temperature high alarm             :  Off
    Module temperature low alarm              :  Off
    Module temperature high warning           :  Off
    Module temperature low warning            :  Off
    Module voltage high alarm                 :  Off
    Module voltage low alarm                  :  Off
    Module voltage high warning               :  Off
    Module voltage low warning                :  Off
    Laser rx power high alarm                 :  Off
    Laser rx power low alarm                  :  On
    Laser rx power high warning               :  Off
    Laser rx power low warning                :  Off
    Laser bias current high alarm threshold   :  79.998 mA
    Laser bias current low alarm threshold    :  0.000 mA
    Laser bias current high warning threshold :  69.998 mA
    Laser bias current low warning threshold  :  3.998 mA
    Laser output power high alarm threshold   :  0.7940 mW / -1.00 dBm
    Laser output power low alarm threshold    :  0.0790 mW / -11.02 dBm
    Laser output power high warning threshold :  0.6300 mW / -2.01 dBm
    Laser output power low warning threshold  :  0.1000 mW / -10.00 dBm
    Module temperature high alarm threshold   :  85 degrees C / 185 degrees
F
    Module temperature low alarm threshold    :  -5 degrees C / 23 degrees F
    Module temperature high warning threshold :  80 degrees C / 176 degrees
F
    Module temperature low warning threshold  :  0 degrees C / 32 degrees F
    Module voltage high alarm threshold       :  3.599 V
    Module voltage low alarm threshold        :  3.000 V
    Module voltage high warning threshold     :  3.499 V
    Module voltage low warning threshold      :  3.100 V
    Laser rx power high alarm threshold       :  0.7943 mW / -1.00 dBm
    Laser rx power low alarm threshold        :  0.0079 mW / -21.02 dBm
    Laser rx power high warning threshold     :  0.6309 mW / -2.00 dBm
    Laser rx power low warning threshold      :  0.0099 mW / -20.04 dBm
                    

ex4200> show interfaces ge-0/1/0 terse 
Interface               Admin Link Proto    Local                 
Remote
ge-0/1/0                up    down
ge-0/1/0.0              up    down eth-switch

ex4200> show chassis hardware 
...
  PIC 0                   BUILTIN      BUILTIN           48x 10/100/1000
Base-T
  PIC 1          REV 04   711-026017   ............      4x GE SFP+
    Xcvr 0       REV 01   740-011614   .........         SFP-LX10


ex4200> show chassis pic fpc-slot 0 pic-slot 1 
FPC slot 0, PIC slot 1 information:
  Type                             4x GE SFP+
  State                            Online    
  PIC version                  1.4
  Uptime                         18 hours, 12 minutes, 48 seconds

PIC port information:
                          Fiber                    Xcvr vendor
  Port  Cable type        type  Xcvr vendor        part number
Wavelength
  0     GIGE 1000LX10     SM    OPNEXT INC         TRF5736AALB214    1310 nm

_______________________________________________
juniper-nsp mailing list juniper-nsp at puck.nether.net
https://puck.nether.net/mailman/listinfo/juniper-nsp