[j-nsp] Juniper 10GE XFP

[Junaid]

Thank you all. It is installed and working ;)

Regards,
Junaid


On Wed, Dec 16, 2009 at 1:55 PM, Martin Levin <martin.levin at molndal.se> wrote:
> Yes, It does if the SFP is Juniper original (or coded as original). This
> is from 10.0 and onwards, before that DOM doesn't exist on an EX.
>
> ---
> Martin Levin
> IT-strategy & planning
> Mölndals stad
>
>
>>>>
>
>
> Från:"Jay Hanke" <jhanke at myclearwave.net>
> Till:"'Chuck Anderson'" <cra at wpi.edu>, <juniper-nsp at puck.nether.net>
> Datum:2009-12-16 01:02
> Ärende:Re: [j-nsp] Juniper 10GE XFP
> Does it also work on a non uplink module ie EX 4200-24F?
>
> -----Original Message-----
> From: juniper-nsp-bounces at puck.nether.net
> [mailto:juniper-nsp-bounces at puck.nether.net] On Behalf Of Chuck
> Anderson
> Sent: Tuesday, December 15, 2009 4:41 PM
> To: juniper-nsp at puck.nether.net
> Subject: Re: [j-nsp] Juniper 10GE XFP
>
> On Mon, Dec 14, 2009 at 03:53:16PM -0600, Jay Hanke wrote:
>> The EX is a different animal, I think there is only support for DOM
>> on the XFP ports unlike the MX where it is supported on all the SFP
>> and XFP ports. Also, I think DOM support is recent (10.0?) on the
>> EX.
>
> No, DOM works on SFP on EX4200 with 10.0.
>
> ex4200> show interfaces diagnostics optics ge-0/1/0
> Physical interface: ge-0/1/0
>    Laser bias current                        :  23.140 mA
>    Laser output power                        :  0.2170 mW / -6.64 dBm
>    Module temperature                        :  47 degrees C / 117
> degrees
> F
>    Module voltage                            :  3.2470 V
>    Receiver signal average optical power     :  0.0006 mW / -32.22
> dBm
>    Laser bias current high alarm             :  Off
>    Laser bias current low alarm              :  Off
>    Laser bias current high warning           :  Off
>    Laser bias current low warning            :  Off
>    Laser output power high alarm             :  Off
>    Laser output power low alarm              :  Off
>    Laser output power high warning           :  Off
>    Laser output power low warning            :  Off
>    Module temperature high alarm             :  Off
>    Module temperature low alarm              :  Off
>    Module temperature high warning           :  Off
>    Module temperature low warning            :  Off
>    Module voltage high alarm                 :  Off
>    Module voltage low alarm                  :  Off
>    Module voltage high warning               :  Off
>    Module voltage low warning                :  Off
>    Laser rx power high alarm                 :  Off
>    Laser rx power low alarm                  :  On
>    Laser rx power high warning               :  Off
>    Laser rx power low warning                :  Off
>    Laser bias current high alarm threshold   :  79.998 mA
>    Laser bias current low alarm threshold    :  0.000 mA
>    Laser bias current high warning threshold :  69.998 mA
>    Laser bias current low warning threshold  :  3.998 mA
>    Laser output power high alarm threshold   :  0.7940 mW / -1.00 dBm
>    Laser output power low alarm threshold    :  0.0790 mW / -11.02
> dBm
>    Laser output power high warning threshold :  0.6300 mW / -2.01 dBm
>    Laser output power low warning threshold  :  0.1000 mW / -10.00
> dBm
>    Module temperature high alarm threshold   :  85 degrees C / 185
> degrees
> F
>    Module temperature low alarm threshold    :  -5 degrees C / 23
> degrees F
>    Module temperature high warning threshold :  80 degrees C / 176
> degrees
> F
>    Module temperature low warning threshold  :  0 degrees C / 32
> degrees F
>    Module voltage high alarm threshold       :  3.599 V
>    Module voltage low alarm threshold        :  3.000 V
>    Module voltage high warning threshold     :  3.499 V
>    Module voltage low warning threshold      :  3.100 V
>    Laser rx power high alarm threshold       :  0.7943 mW / -1.00 dBm
>    Laser rx power low alarm threshold        :  0.0079 mW / -21.02
> dBm
>    Laser rx power high warning threshold     :  0.6309 mW / -2.00 dBm
>    Laser rx power low warning threshold      :  0.0099 mW / -20.04
> dBm
>
>
> ex4200> show interfaces ge-0/1/0 terse
> Interface               Admin Link Proto    Local
> Remote
> ge-0/1/0                up    down
> ge-0/1/0.0              up    down eth-switch
>
> ex4200> show chassis hardware
> ...
>  PIC 0                   BUILTIN      BUILTIN           48x
> 10/100/1000
> Base-T
>  PIC 1          REV 04   711-026017   ............      4x GE SFP+
>    Xcvr 0       REV 01   740-011614   .........         SFP-LX10
>
>
> ex4200> show chassis pic fpc-slot 0 pic-slot 1
> FPC slot 0, PIC slot 1 information:
>  Type                             4x GE SFP+
>  State                            Online
>  PIC version                  1.4
>  Uptime                         18 hours, 12 minutes, 48 seconds
>
> PIC port information:
>                          Fiber                    Xcvr vendor
>  Port  Cable type        type  Xcvr vendor        part number
> Wavelength
>  0     GIGE 1000LX10     SM    OPNEXT INC         TRF5736AALB214
> 1310 nm
>
> _______________________________________________
> juniper-nsp mailing list juniper-nsp at puck.nether.net
> https://puck.nether.net/mailman/listinfo/juniper-nsp
>
> _______________________________________________
> juniper-nsp mailing list juniper-nsp at puck.nether.net
> https://puck.nether.net/mailman/listinfo/juniper-nsp
> _______________________________________________
> juniper-nsp mailing list juniper-nsp at puck.nether.net
> https://puck.nether.net/mailman/listinfo/juniper-nsp



-- 

Regards,
Junaid