[j-nsp] Logical Interfaces 802.1ad
Onam Rubio
onamrubio at hotmail.com
Tue Oct 20 12:50:30 EDT 2009
Hello,
Here, is the information. but the Junipes's don't see each other.
onam at M10_A> show configuration interfaces ge-0/2/0
flexible-vlan-tagging;
gigether-options {
ethernet-switch-profile {
tag-protocol-id 0x88a8;
}
}
unit 50 {
vlan-tags outer 0x88a8.50 inner 100;
family inet {
address 192.168.38.58/30;
}
}
onam at M10_A> show interfaces ge-0/2/0.100 | match Encapsulation
onam at M10_Ashow interfaces ge-0/2/0 | match Encapsulation
Flags: SNMP-Traps VLAN-Tag [ 0x0000.0 ] Encapsulation: ENET2
onam at M5_B> show configuration interfaces ge-0/2/0
flexible-vlan-tagging;
gigether-options {
ethernet-switch-profile {
tag-protocol-id 0x88a8;
}
}
unit 50 {
vlan-tags outer 0x88a8.50 inner 100;
family inet {
address 192.168.38.57/30;
}
}
onam at MetisM5_B> show interfaces ge-0/2/0.100 | match Encapsulation
onam at MetisM5_B> show interfaces ge-0/2/0 | match Encapsulation
Flags: SNMP-Traps VLAN-Tag [ 0x0000.0 ] Encapsulation: ENET2
Summit
x450_A# sho vman etherType
vman EtherType : 0x88a8
x450_A# # SHO vman "Test_Side_A"
VMAN Interface with name Test_Side_A created by user
Admin State: Enabled Tagging: 802.1Q Tag 50
Virtual router: VR-Default
**Primary IP : 192.168.175.166/28 **(Administration IP address)**
IPv6: None
STPD: None
Protocol: Match all unfiltered protocols
Loopback: Disabled
NetLogin: Disabled
QosProfile: None configured
Egress Rate Limit Designated Port: None configured
Ports: 4. (Number of active ports=3)
Tag: *1(UpLink_x450_B),*46(M10_A_Ge-0/2/0)
Flags: (*) Active, (!) Disabled, (g) Load Sharing port
(b) Port blocked on the vlan, (a) Authenticated NetLogin port
(u) Unauthenticated NetLogin port, (m) Mac-Based port
x450_A#
x450_B # sh vman etherType
Vman Primary EtherType : 0x88a8
x450_B # sho vman "Test_Side_B"
VMAN Interface with name Test_Side_B created by user
Admin State: Enabled Tagging: 802.1Q Tag 50
Virtual router: VR-Default
**Primary IP : 172.16.40.2/24** (Administration IP address)**
IPv6: None
STPD: None
Protocol: Match all unfiltered protocols
Loopback: Disabled
NetLogin: Disabled
QosProfile: None configured
Egress Rate Limit Designated Port: None configured
Flood Rate Limit QosProfile: None configured
Ports: 20. (Number of active ports=15)
Tag: *1(UpLink_x450_A),*45(M5_B_Ge-0/2/0)
Flags: (*) Active, (!) Disabled, (g) Load Sharing port
(b) Port blocked on the vlan, (m) Mac-Based port
(a) Egress traffic allowed for NetLogin
(u) Egress traffic unallowed for NetLogin
x450_B#
Best regards.
> Date: Tue, 20 Oct 2009 11:15:37 +0300
> From: evgeniy at ip.datagroup.ua
> To: onamrubio at hotmail.com
> Subject: Re[4]: [j-nsp] Logical Interfaces 802.1ad
>
> Hi Onam,
> I examined you config and at first glance all should works....
> Please show from both Junipers:
> show interfaces xxx.100 | match Encapsulation
>
> From both Summits:
> show vman etherType
> show vman xxx
>
>
>
> best regards,
> --
> Evgeniy Aikashev
> network engineer
> JSC DATAGROUP
>
> Tuesday, October 20, 2009, 9:45:37 AM, Onam wrote:
> > Dear Evgenie,
>
> > Thaks for your help.
>
> > But I configure the juniper as you suggest me, but it doesn't work. I don't know if I'am missing a parameter or something else.
>
> > I sent you the topology, maybe you can check it.
>
> > I just try the same with to Cisco router at the same topology and it works, in fact I test it with 0x88a8 and 0x9100.
>
> > Best regards.
>
> >> Date: Mon, 19 Oct 2009 10:47:16 +0300
> >> From: evgeniy at ip.datagroup.ua
> >> To: onamrubio at hotmail.com
> >> CC: juniper-nsp at puck.nether.net
> >> Subject: Re[2]: [j-nsp] Logical Interfaces 802.1ad
> >>
> >> Also works fine:
> >>
> >> {master}[edit interfaces xe-4/1/0]
> >> evgeniy at mx480# show
> >> description "=== Summit X650 test ===";
> >> flexible-vlan-tagging;
> >> encapsulation flexible-ethernet-services;
> >> gigether-options {
> >> ethernet-switch-profile {
> >> tag-protocol-id 0x88a8;
> >> }
> >> }
> >> unit 100 {
> >> description "=== Summit X650 test ===";
> >> vlan-tags outer 0x88a8.4092 inner 100;
> >> family inet {
> >> address x.x.x.x/30;
> >> }
> >> }
> >>
> >> Summit:
> >> enable jumbo-frame ports all
> >>
> >>
> >> best regards,
> >> --
> >> Evgeniy Aikashev
> >> network engineer
> >> JSC DATAGROUP
> >>
> >> Monday, October 19, 2009, 10:17:22 AM, Onam wrote:
> >> > Hello Evgeniy,
> >>
> >> > I made some test before with this ethertype and it works. The Extreme x450 use both of them
> >> > 0x8100 for VLAN and 0x88a8 for VMAN so if i do that the VMAN will become a VLAN.
> >>
> >> > I see that by default the Juniper router M10 use ethertype 0x8100, but when I try to use
> >> > ethertype 0x88a8 the devices doens't see each other, I run a ping to the other side with no response.
> >>
> >>
> >> >> Date: Mon, 19 Oct 2009 09:58:23 +0300
> >> >> From: evgeniy at ip.datagroup.ua
> >> >> To: onamrubio at hotmail.com
> >> >> CC: juniper-nsp at puck.nether.net
> >> >> Subject: Re: [j-nsp] Logical Interfaces 802.1ad
> >> >>
> >> >> Hello Onam,
> >> >> try to change ethertype from Summit side:
> >> >>
> >> >> configure vman ethertype 0x8100
> >> >>
> >> >> best regards,
> >> >> --
> >> >> Evgeniy Aikashev
> >> >> network engineer
> >> >> JSC DATAGROUP
> >> >>
> >> >> Monday, October 19, 2009, 3:30:51 AM, Onam wrote:
> >> >>
> >> >> > Hi experts,
> >> >>
> >> >> > I want to make logical interfaces on a physical interface ge-0/2/0 of a Juniper M10 router to
> >> >> > connected to a the trunk port of a Summit Extreme x450 with the ethertype 0x88a8 (IEEE 802.1ad).
> >> >>
> >> >> > I have the following configuration on the router.
> >> >>
> >> >> > ge-0/2/0 {
> >> >> > vlan-tagging;
> >> >> > gigether-options {
> >> >> > ethernet-switch-profile {
> >> >> > tag-protocol-id 0x88a8;
> >> >> > }
> >> >> > }
> >> >> > unit 50 {
> >> >> > vlan-tags outer 0x88a8.50;
> >> >> > family inet {
> >> >> > address 192.168.175.169/28;
> >> >> > }
> >> >> > }
> >> >> > }
> >> >>
> >> >> > I made the test with the 802.1q and it works but with 802.1ad didn't work.
> >> >>
> >> >> > Best regards.
> >> >> >
> >> >> > _________________________________________________________________
> >> >> > News, entertainment and everything you care about at Live.com. Get it now!
> >> >> > http://www.live.com/getstarted.aspx
> >> >> > _______________________________________________
> >> >> > juniper-nsp mailing list juniper-nsp at puck.nether.net
> >> >> > https://puck.nether.net/mailman/listinfo/juniper-nsp
> >> >>
> >>
> >> > Get news, entertainment and everything you care about at Live.com. Check it out!
> >>
>
> > Invite your mail contacts to join your friends list with Windows Live Spaces. It's easy! Try it!
>
_________________________________________________________________
Connect to the next generation of MSN Messenger
http://imagine-msn.com/messenger/launch80/default.aspx?locale=en-us&source=wlmailtagline
More information about the juniper-nsp
mailing list