[j-nsp] ipv6 routing

Thu Apr 1 02:50:59 EDT 2010

Hi Serge,

The M10i is running on ipv4 (bgp, ospf, including static)from beginning with
neighbor Cisco routers, now the requirement is to add enable dual stacking
(v4 and v6) routing like ospf and bgp on the same platform. I haven’t faced
any vendor compatibility issues between them on ipv4. And still I don’t
think the problem is by multi vendors.

here, the output of M10i :

 run show interfaces fe-0/1/0
 Physical interface: fe-0/1/0, Enabled, Physical link is Up
  Interface index: 129, SNMP ifIndex: 123
  Description: Connected to Beetle for iBGP peering
  Link-level type: Ethernet, MTU: 1514, Link-mode: Full-duplex, Speed:
100mbps, MAC-REWRITE Error: None, Loopback: Disabled,
  Source filtering: Disabled, Flow control: Enabled
  Device flags   : Present Running
  Interface flags: SNMP-Traps Internal: 0x4000
  CoS queues     : 4 supported, 4 maximum usable queues
  Current address: 00:17:cb:77:00:1f, Hardware address: 00:17:cb:77:00:1f
  Last flapped   : 2010-03-15 11:23:26 NPT (2w3d 00:57 ago)
  Input rate     : 126752 bps (22 pps)
  Output rate    : 87384 bps (46 pps)
  Active alarms  : None
  Active defects : None

  Logical interface fe-0/1/0.0 (Index 69) (SNMP ifIndex 127)
    Flags: SNMP-Traps Encapsulation: ENET2
    Input packets : 31156647
    Output packets: 18571460
    Protocol inet, MTU: 1500
      Flags: None
      Addresses, Flags: Is-Preferred Is-Primary
        Destination: x.x.193.0/28, Local: x.x.193.1, Broadcast: x.x.193.15
    Protocol inet6, MTU: 1500
      Flags: None
      Addresses, Flags: Is-Preferred Is-Primary
        Destination: abcd:3800:2:1::/126, Local: abcd:3800:2:1::1
      Addresses, Flags: Is-Preferred
        Destination: fe80::/64, Local: fe80::217:cbff:fe77:1f

run show version
Hostname: host-m10i
Model: m10i
JUNOS Base OS boot [9.2R2.15]
JUNOS Base OS Software Suite [9.2R2.15]
JUNOS Kernel Software Suite [9.2R2.15]
JUNOS Crypto Software Suite [9.2R2.15]
JUNOS Packet Forwarding Engine Support (M/T Common) [9.2R2.15]
JUNOS Packet Forwarding Engine Support (M7i/M10i) [9.2R2.15]
JUNOS Online Documentation [9.2R2.15]
JUNOS Routing Software Suite [9.2R2.15]

run show ospf3 overview
OSPF instance is not running

run show configuration protocols ospf3
preference 110;
area 0.0.0.10 {
    interface fe-0/1/0.0;
    interface ge-0/0/0.0;
    interface lo0.0 {
        passive;

Cisco output :

#show run | be ^ipv6 router

ipv6 router ospf 200
 router-id x.x.192.10
 log-adjacency-changes

#sh run int lo6
Building configuration...

Current configuration : 157 bytes
!
interface Loopback6
 ip address x.x.192.10 255.255.255.255
 ipv6 address abcd:3800::4/128
 ipv6 enable
 ipv6 ospf 200 area 10
 no clns route-cache
end

sh run int fa0/0
Building configuration...

Current configuration : 264 bytes
!
interface FastEthernet0/0
 description *** iBGP peering ***
 ip address x.x.193.4 255.255.255.240
 no keepalive
 duplex full
 ipv6 address abcd:3800:2:1::2/126
 ipv6 enable
 ipv6 ospf 200 area 10
 no cdp enable
 no clns route-cache
end

Thank you,

On Thu, Apr 1, 2010 at 3:26 AM, Serge Vautour <sergevautour at yahoo.ca> wrote:

> Hello,
>
> Can you post the following to the mailing list?
>
> -show int ge-0/0/0
> -show version
> -show ospf3 overview
>
> From the Cisco router:
> -The interface and OSPF config
>
> I'm assuming IPv4 ping works over the interface?
>
>
> Thanks,
> Serge
>
>
> ----- Original Message ----
> From: Ramesh Karki <rameshkarki at gmail.com>
> To: Antonio Querubin <tony at lava.net>
> Cc: juniper-nsp at puck.nether.net
> Sent: Wed, March 31, 2010 4:54:29 PM
> Subject: Re: [j-nsp] ipv6 routing
>
> Hi,
> Similar ospf config between cisco to cisco is okay there is not any issue.
> But between cisco to M10i is not working.
> Here, I have listed my JunOS ospf config :
> run show configuration protocols ospf3
> preference 10;
> area 0.0.0.10 {
>    interface lo0.0 {
>        passive;
>    }
>    interface ge-0/0/0.0 {
>        metric 10;
>
> am I missing anything ??
>
> My curiosity : when I execute the command > run show ospf3 interface
> ge-0/0/0.0 it says -
> “OSPF instance is not running” ??
>
> Thank you,
>
>
> On Thu, Apr 1, 2010 at 1:12 AM, Antonio Querubin <tony at lava.net> wrote:
>
> > On Thu, 1 Apr 2010, Ramesh Karki wrote:
> >
> >  I have also tried to run ospf3 but no luck, the command > show ospf3
> >> interface ge-0/0/0.0 says
> >> “OSPF instance is not running”
> >>
> >
> >  I have tried run ospf3 but no luck, the command > show ospf3 interface
> >>> ge-0/0/0.0 says
> >>> “OSPF instance is not running”
> >>>
> >>
> > What does your ospf3 config look like on the M10?  What does it look like
> > on the Cisco?
> >
> >
> > Antonio Querubin
> > 808-545-5282 x3003
> > e-mail/xmpp:  tony at lava.net
> >
> _______________________________________________
> juniper-nsp mailing list juniper-nsp at puck.nether.net
> https://puck.nether.net/mailman/listinfo/juniper-nsp
>
>
>
>       __________________________________________________________________
> Yahoo! Canada Toolbar: Search from anywhere on the web, and bookmark your
> favourite sites. Download it now
> http://ca.toolbar.yahoo.com.
>