[j-nsp] EX4200 Problem - Bad Switch?
Paul Stewart
paul at paulstewart.org
Mon Jan 10 18:12:49 EST 2011
Thanks.. going to try a few things and if not we'll RMA it via JTAC....
Paul
-----Original Message-----
From: Bill Blackford [mailto:BBlackford at nwresd.k12.or.us]
Sent: January-10-11 5:52 PM
To: Paul Stewart; 'Joe Hamelin'
Cc: 'juniper-nsp'
Subject: RE: [j-nsp] EX4200 Problem - Bad Switch?
I was going to suggest looking at the caveats on Juniper's site regarding
JUNOS levels and upgrading. IOW, if it shipped with certain 9.x versions you
have to incrementally get to 10.x, however, reading further I see you had it
successfully booted.
I did have a EX3200-24T come back up in factory default once. I had JTAC
replace the hardware. Unfortunately, I can't recall the details. After
viewing the crash dump and logs, they claimed I issued a factory reset
command (which I did not). I told I don't trust this piece of hardware, so
they RMA'd it for me.
I don't know if this helps, but it may be something to think about.
-b
-----Original Message-----
From: juniper-nsp-bounces at puck.nether.net
[mailto:juniper-nsp-bounces at puck.nether.net] On Behalf Of Paul Stewart
Sent: Monday, January 10, 2011 2:37 PM
To: 'Joe Hamelin'
Cc: 'juniper-nsp'
Subject: Re: [j-nsp] EX4200 Problem - Bad Switch?
Thanks.. this was a brand new out of the box switch. It had been powered up
once successfully and worked "fine" at that point. Then it was powered down
and brought back up and now problems...
Tried 3 times now to reinstall JunOS and no luck ;(
-----Original Message-----
From: nethead at gmail.com [mailto:nethead at gmail.com] On Behalf Of Joe Hamelin
Sent: January-10-11 4:07 PM
To: Paul Stewart
Cc: juniper-nsp
Subject: Re: [j-nsp] EX4200 Problem - Bad Switch?
It looks like you're missing a few libraries (files) in your install.
Re-install JunOS.
--
Joe Hamelin, W7COM, Tulalip, WA, 360-474-7474
On Mon, Jan 10, 2011 at 12:53 PM, Paul Stewart <paul at paulstewart.org> wrote:
> Hey folks.
>
> Ran across a weird issue today on a new EX4200-48T switch. Switch boots
up
> and during so I see this (sorry for the length of the post):
>
> Trying to mount root from ufs:/dev/da0s1a
> Attaching /packages/jbase via /dev/mdctl...
> Mounted jbase package on /dev/md0...
> Verified manifest signed by PackageProduction_10_0_0
> Verified jboot signed by PackageProduction_10_0_0
> Verified jbase-10.0R4.7 signed by PackageProduction_10_0_0
> /packages/jcrypto-ex-10.0R4.7 not present.
> /packages/jdocs-ex-10.0R4.7 not present.
> Mounted jkernel-ex package on /dev/md1...
> Verified manifest signed by PackageProduction_10_0_0
> Verified jkernel-ex-10.0R4.7 signed by PackageProduction_10_0_0
> Mounted jpfe-ex42x package on /dev/md2...
> Verified manifest signed by PackageProduction_10_0_0
> Verified jpfe-ex42x-10.0R4.7 signed by PackageProduction_10_0_0
> Mounted jroute-ex package on /dev/md3...
> Verified manifest signed by PackageProduction_10_0_0
> Verified jroute-ex-10.0R4.7 signed by PackageProduction_10_0_0
> /packages/jswitch-ex-10.0R4.7 not present.
> Mounted jweb-ex package on /dev/md4...
> Verified manifest signed by PackageProduction_10_0_0
> Verified jweb-ex-10.0R4.7 signed by PackageProduction_10_0_0
> Executing /packages/mnt/jweb-ex-10.0R4.7/mount.post..
> Automatic reboot in progress...
> FILE SYSTEM CLEAN; SKIPPING CHECKS
> clean, 48430 free (46 frags, 6048 blocks, 0.0% fragmentation)
> FILE SYSTEM CLEAN; SKIPPING CHECKS
> clean, 28254 free (38 frags, 3527 blocks, 0.1% fragmentation)
> FILE SYSTEM CLEAN; SKIPPING CHECKS
> clean, 62228 free (244 frags, 7748 blocks, 0.4% fragmentation)
> FILE SYSTEM CLEAN; SKIPPING CHECKS
> clean, 160996 free (28 frags, 20121 blocks, 0.0% fragmentation)
> FILE SYSTEM CLEAN; SKIPPING CHECKS
> clean, 160996 free (28 frags, 20121 blocks, 0.0% fragmentation)
> Creating initial configuration...mgd: error: Couldn't open lib
> "/usr/lib/dd//libjcrypto-dd.so": Cannot open
"/usr/lib/dd//libjcrypto-dd.so"
> mgd: error: Couldn't open lib "/usr/lib/dd//libjcrypto_junos-dd.so":
Cannot
> open "/usr/lib/dd//libjcrypto_junos-dd.so"
> mgd: error: Couldn't open lib "/usr/lib/dd//libjdocs-dd.so": Cannot open
> "/usr/lib/dd//libjdocs-dd.so"
> /config/juniper.conf:294:(8) syntax error at 'rstp'
> [edit protocols]
> 'rstp;'
> syntax error
> /config/juniper.conf:297:(5) error recovery ignores input until this point
> at '}'
> [edit protocols]
> '}'
> error recovery ignores input until this point
> /config/juniper.conf:300:(5) error recovery ignores input until this point
> at '}'
> [edit protocols]
> '}'
> error recovery ignores input until this point
> /config/juniper.conf:304:(1) error recovery ignores input until this point
> at '}'
> [edit]
> '}'
> error recovery ignores input until this point
> [edit system services ssh]
> 'ssh'
> warning: daemon binary /usr/sbin/sshd not found
> mgd: commit complete
> Setting initial options: debugger_on_panic=NO debugger_on_break=NO.
> Starting optional daemons: OK: extracted home directories.
> .
> Doing initial network setup:
> .
> Initial interface configuration:
> additional daemons:.
> Additional routing options:kern.module_path: /boot//kernel;/bootLoading
the
> NETPFE ethernet module
> /modules -> /booLoading the EX-series platform NETPFE module
> t//kernel;/boot/modules;/modules
> grat_arp_on_ifup=YES: net.link.ether.inet.grat_arp_on_ifup: 1 -> 1
> grat_arp_delay=${grat_arp_delay}: net.link.ether.inet.grat_arp_delay: 0 ->
0
> kld netpfe drv: ifpfed_ethkld platform: ex_ifpfe if_vcpkern.module_path:
> /boot//kernel;/boot/modules;/modules ->
> /boot//kernel;/boot/modules;/modules;/modules/peertype
> kld peertype: peertype_hcm peertype_pfem peertype_sfi peertype_slavere.
> Doing additional network setup:.
> Starting final network daemons:.
> setting ldconfig path: /usr/lib /opt/lib
> ldconfig: warning: /opt/lib: No such file or directory
> starting standard daemons: cron.
> Local package initialization:.
> kern.securelevel: -1 -> 1
> starting local daemons:.
> Thu Oct 14 06:24:18 UTC 2010
>
> Amnesiac (ttyu0)
>
>
>
> So I thought that perhaps the JunOS install is corrupt and rebooted with
my
> USB drive connected. Ran through the installation and it won't complete:
>
>
> loader> install file:///jinstall-ex-4200-10.0R4.7-domestic-signed.tgz
> Package /jinstall-ex-4200-10.0R4.7-domestic-signed.tgz is signed...
> /kernel data=0x4efa0c+0x51a94 syms=[0x4+0x4e100+0x4+0x707d3]
> Kernel entry at 0xa00000e0 ...
> GDB: no debug ports present
> KDB: debugger backends: ddb
> KDB: current backend: ddb
> platform_early_bootinit: EX Series Early Boot Initialization
> Copyright (c) 1996-2010, Juniper Networks, Inc.
> All rights reserved.
> Copyright (c) 1992-2006 The FreeBSD Project.
> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
> The Regents of the University of California. All rights reserved.
> JUNOS 10.0R4.7 #0: 2010-08-22 02:45:23 UTC
>
>
builder at ormonth.juniper.net:/volume/build/junos/10.0/release/10.0R4.7/obj-po
> Timecounter "decrementer" frequency 50000000 Hz quality 0
> cpu0: Freescale e500v2 core revision 2.2
> cpu0: HID0 80004080<EMCP,TBEN,EN_MAS7_UPDATE>
> real memory = 1044381696 (996 MB)
> avail memory = 1022767104 (975 MB)
> ETHERNET SOCKET BRIDGE initialising
> Initializing EXSERIES platform properties ...
> nexus0: <PPC e500 Nexus device>
> ocpbus0: <on-chip peripheral bus> on nexus0
> openpic0: <OpenPIC in on-chip peripheral bus> iomem 0xfef40000-0xfef600b3
on
> ocpbus0
> uart0: <16550 or compatible> iomem 0xfef04500-0xfef0450f irq 58 on ocpbus0
> uart0: console (9600,n,8,1)
> uart1: <16550 or compatible> iomem 0xfef04600-0xfef0460f irq 58 on ocpbus0
> lbc0: <Freescale 8533 Local Bus Controller> iomem
> 0xfef05000-0xfef05fff,0xff000000-0xffffffff irq 22 on ocpbus0
> cfi0: <AMD/Fujitsu - 8MB> iomem 0xff800000-0xffffffff on lbc0
> syspld0 iomem 0xff000000-0xff00ffff on lbc0
> tsec0: <eTSEC ethernet controller> iomem 0xfef24000-0xfef24fff irq
45,46,50
> on ocpbus0
> tsec0: hardware MAC address b0:c6:9a:61:96:7f
> miibus0: <MII bus> on tsec0
> e1000phy0: <Marvell 88E1112 Gigabit PHY> on miibus0
> e1000phy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX,
1000baseTX-FDX,
> auto
> pcib0: <Freescale MPC8544 PCI host controller> iomem
> 0xfef08000-0xfef08fff,0xf0000000-0xf3ffffff on ocpbus0
> pci0: <PCI bus> on pcib0
> pci0: <serial bus, USB> at device 18.0 (no driver attached)
> ehci0: <Philips ISP156x USB 2.0 controller> mem 0xf0001000-0xf00010ff irq
22
> at device 18.2 on pci0
> usb0: EHCI version 1.0
> usb0: <Philips ISP156x USB 2.0 controller> on ehci0
> usb0: USB revision 2.0
> uhub0: Philips EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
> uhub0: 2 ports with 2 removable, self powered
> umass0: STMicroelectronics ST72682 High Speed Mode, rev 2.00/2.10, addr 2
> umass1: SanDisk MobileMate Micro, rev 2.00/94.07, addr 3
> pcib1: <Freescale MPC8544 PCI Express host controller> iomem
> 0xfef0a000-0xfef0afff,0xe0000000-0xe3ffffff,0xec000000-0xec0fffff irq 42
on
> ocpbus0
> pci1: <PCI bus> on pcib1
> pcib2: <PCI-PCI bridge> at device 0.0 on pci1
> pci2: <PCI bus> on pcib2
> pci2: <memory> at device 0.0 (no driver attached)
> pcib3: <Freescale MPC8544 PCI Express host controller> iomem
> 0xfef09000-0xfef09fff,0xe4000000-0xe7ffffff,0xec100000-0xec1fffff irq 41
on
> ocpbus0
> pci3: <PCI bus> on pcib3
> pcib4: <PCI-PCI bridge> at device 0.0 on pci3
> pci4: <PCI bus> on pcib4
> pci4: <memory> at device 0.0 (no driver attached)
> pcib5: <Freescale MPC8544 PCI Express host controller> iomem
> 0xfef0b000-0xfef0bfff,0xe8000000-0xebffffff,0xec200000-0xec2fffff irq 43
on
> ocpbus0
> pci5: <PCI bus> on pcib5
> pcib6: <PCI-PCI bridge> at device 0.0 on pci5
> pci6: <PCI bus> on pcib6
> pci6: <memory> at device 0.0 (no driver attached)
> i2c0: <MPC85XX OnChip i2c controller> iomem 0xfef03000-0xfef03014 irq 59
on
> ocpbus0
> i2c1: <MPC85XX OnChip i2c controller> iomem 0xfef03100-0xfef03114 irq 59
on
> ocpbus0
> Timecounters tick every 10.000 msec
> md0: Preloaded image </isofs-install-ex> 10477568 bytes at 0xa05ffd7c
> da1 at umass-sim1 bus 1 target 0 lun 0
> da1: <Generic STORAGE DEVICE 9407> Removable Direct Access SCSI-0 device
> da1: 40.000MB/s transfers
> da1: 1910MB (3911680 512 byte sectors: 255H 63S/T 243C)
> da0 at umass-sim0 bus 0 target 0 lun 0
> da0: <ST ST72682 2.10> Removable Direct Access SCSI-2 device
> da0: 40.000MB/s transfers
> da0: 1000MB (2048000 512 byte sectors: 64H 32S/T 1000C)
> Trying to mount root from cd9660:/dev/md0
> FILE SYSTEM CLEAN; SKIPPING CHECKS
> clean, 160996 free (28 frags, 20121 blocks, 0.0% fragmentation)
> tunefs: soft updates remains unchanged as disabled
> FILE SYSTEM CLEAN; SKIPPING CHECKS
> clean, 28254 free (38 frags, 3527 blocks, 0.1% fragmentation)
> /dev/da0s2a: 187.2MB (383352 sectors) block size 16384, fragment size 2048
> using 4 cylinder groups of 46.80MB, 2995 blks, 6016 inodes.
> with soft updates
> super-block backups (for fsck -b #) at:
> 32, 95872, 191712, 287552
> /dev/da0s2f: 124.8MB (255584 sectors) block size 16384, fragment size 2048
> using 4 cylinder groups of 31.20MB, 1997 blks, 4096 inodes.
> with soft updates
> super-block backups (for fsck -b #) at:
> 32, 63936, 127840, 191744
> Installing disk1:/jinstall-ex-4200-10.0R4.7-domestic-signed.tgz
> /dev/da0s3d: 319.6MB (654524 sectors) block size 16384, fragment size 2048
> using 4 cylinder groups of 79.91MB, 5114 blks, 10240 inodes.
> super-block backups (for fsck -b #) at:
> 32, 163680, 327328, 490976
> tty: not found
> tty: not found
> tty: not found
> tty: not found
> date: connect: Can't assign requested address
> Checking package integrity...
> Verified SHA1 checksum of jbase-ex-10.0R4.7.tgz
> Verified SHA1 checksum of jboot-ex-10.0R4.7.tgz
> Verified SHA1 checksum of jcrypto-ex-10.0R4.7.tgz
> Verified SHA1 checksum of jdocs-ex-10.0R4.7.tgz
> Verified SHA1 checksum of jkernel-ex-10.0R4.7.tgz
> Verified SHA1 checksum of jpfe-ex42x-10.0R4.7.tgz
> Verified SHA1 checksum of jroute-ex-10.0R4.7.tgz
> Verified SHA1 checksum of jswitch-ex-10.0R4.7.tgz
> Verified SHA1 checksum of jweb-ex-10.0R4.7.tgz
> Running requirements check first for jbundle-ex-4200-10.0R4.7-domestic...
> Running pre-install for jbundle-ex-4200-10.0R4.7-domestic...
> Installing jbundle-ex-4200-10.0R4.7-domestic in
> /tmp/pa2398.26/jbundle-ex-4200-10.0R4.7-domestic.x2398...
> Running post-install for jbundle-ex-4200-10.0R4.7-domestic...
> Adding jkernel-ex...
> Adding jcrypto-ex...
> Adding jdocs-ex...
> Adding jswitch-ex...
> Adding jpfe-ex42x...
> Adding jroute-ex...
> Adding jweb-ex...
> Saving home directories
> *** The installer exited with status 2 ***
> *** The installation is unsuccessful!!! ***
> A shell has been started. type exit<cr> to reboot:
>
>
> Is this a bad switch??
>
> Thanks in advance,
>
> Paul
>
>
>
> _______________________________________________
> juniper-nsp mailing list juniper-nsp at puck.nether.net
> https://puck.nether.net/mailman/listinfo/juniper-nsp
>
_______________________________________________
juniper-nsp mailing list juniper-nsp at puck.nether.net
https://puck.nether.net/mailman/listinfo/juniper-nsp
More information about the juniper-nsp
mailing list