[j-nsp] VPLS Between 2 Routers

[David Ball]

  Try adding the interface (ge-0/0/7.0) under the 'site' definition in the
routing instance config.....it's required, as far as I know.  The rest
looks pretty familiar.

David


On 1 March 2012 17:06, Craig Whitmore <lennon at orcon.net.nz> wrote:

> Hi there
>
> I am pretty new to MPLS but what I'm trying to do is set up a L2 Tunnel
> between 2 Routers  via VPLS. The idea is the customer can plug a TRUNK port
> at both ends and run whatever VLANS they want between them . Maybe there is
> a easier way to do it. There are LOTS of examples in LOTS of different
> places on how VPLS should be set up and all are slightly different. I
> cannot
> get any data thru the VPLS connection..
>
> The set up is 2 Juniper Routers running OSPF between them and then BGP
> between the Loopbacks also running MPLS/LDP etc
>
> The Config is (the same on both ends basically)
>
> ge-0/0/7 {
>    description "VPLS";
>    per-unit-scheduler;
>    encapsulation ethernet-vpls;
>    unit 0 {
>        family vpls;
>    }
> }
>
> VPLS-Customer {
>    instance-type vpls;
>    interface ge-0/0/7.0;
>    route-distinguisher XXXXX:2000;  (XXXXXX:1000 on other side).. (XXXX =
> the AS number)
>    vrf-target target:XXXXX:100;
>    protocols {
>        vpls {
>            site-range 10;
>            no-tunnel-services;
>            site router-2000 {
>                site-identifier 5; (different on both sides)
>            }
>        }
>    }
> }
>
>
> Debug..
>
> # show vpls connections  extensive
>
> Instance: VPLS-Customer
>  Local site: router-2000 (5)
>    Number of local interfaces: 1
>    Number of local interfaces up: 1
>    IRB interface present: no
>    ge-0/0/7.0
>    lsi.1049090         6         Intf - vpls VPLS-Customer local site 5
> remote site 6
>    Label-base        Offset     Size  Range     Preference
>    262153            1          8      8         100
>    connection-site           Type  St     Time last up          # Up trans
>    6                         rmt   Up     Mar  2 11:32:17 2012           1
>      Remote PE: Y.Y.Y.Y, Negotiated control-word: No (Y.Y.Y.Y = Loopback of
> other router)
>      Incoming label: 262158, Outgoing label: 262165
>      Local interface: lsi.1049090, Status: Up, Encapsulation: VPLS
>        Description: Intf - vpls VPLS-Customer local site 5 remote site 6
>    Connection History:
>        Mar  2 11:32:17 2012  status update timer
>        Mar  2 11:32:17 2012  loc intf up                  lsi.1049090
>        Mar  2 11:32:17 2012  PE route changed
>        Mar  2 11:32:17 2012  Out lbl Update                    262165
>        Mar  2 11:32:17 2012  In lbl Update                     262158
>        Mar  2 11:32:17 2012  loc intf down
>
>
> #show bgp summary instance VPLS-Customer
>
> Groups: 0 Peers: 0 Down peers: 0
> Table          Tot Paths  Act Paths Suppressed    History Damp State
> Pending
> VPLS.l2vpn.0           1          1          0          0          0
> 0
>
> # show bgp summary.
>
> Peer                     AS      InPkt     OutPkt    OutQ   Flaps Last
> Up/Dwn State|#Active/Received/Accepted/Damped...
> Y.Y.Y.Y           56030       6057       4657       0       0 1d 11:40:03
> Establ (Y.Y.Y.Y = IP Address of other routers loopback)
>  inet.0: 2/5156/2/0
>  inet.2: 0/0/0/0
>  bgp.l2vpn.0: 1/1/1/0
>  bgp.l3vpn.0: 0/0/0/0
>  VPLS-Customer.l2vpn.0: 1/1/1/0
>
>
>
>
>
>
> _______________________________________________
> juniper-nsp mailing list juniper-nsp at puck.nether.net
> https://puck.nether.net/mailman/listinfo/juniper-nsp
>