[j-nsp] Juniper SRX 240 Clustering

[Bikash Bhattarai]

Dear Wasterlund,

I am not using any kind of configuration except junos CLI. I have followed
below configuration guide from juniper.
http://kb.juniper.net/library/CUSTOMERSERVICE/technotes/8010055-EN.PDF

While setting hostname and ip address I have used  set apply-groups "node0"
instead of set apply-groups “${node}” . Is that making issue while failover
?


Regards,
Bikash Bhattarai | Dristi Tech (P.) Ltd | +977 9851039710 |
www.dristi.com.np
Lazimpat, Kathmandu |Tel  977 1 4427949  |  Fax 977 1 4410385*

*




On Sun, Nov 25, 2012 at 4:12 PM, Per Westerlund <p1 at westerlund.se> wrote:

> Strange, this is from a production system:
>
> apply-groups [ "${node}" rfc-5735 ];
>
> (where rfc-5735 is a group that not is relevant for this discussion). This
> line is manually configured, not something that is an effect of activating
> cluster mode. Are you running some kind of tool setting up the clustering
> and configuration instead of straight CLI?
>
> This is the version we are running:
>
> {primary:node1}
> adm_perw at dkcphfw01b> show version
> node0:
> --------------------------------------------------------------------------
> Hostname: dkcphfw01a
> Model: srx550
> JUNOS Software Release [12.1R2.9]
>
> node1:
> --------------------------------------------------------------------------
> Hostname: dkcphfw01b
> Model: srx550
> JUNOS Software Release [12.1R2.9]
>
> /Per Westerlund
>
>
> 25 nov 2012 kl. 07:11 skrev Bikash Bhattarai:
>
> Dear Westerlund,
>
> Thank you for your email. When I configure clustering all the
> configuration automatically moves to apply-groups [ node0 node1 ].
>
>
>  Regards,
> Bikash Bhattarai | Dristi Tech (P.) Ltd | +977 9851039710 |
> www.dristi.com.np
> Lazimpat, Kathmandu |Tel  977 1 4427949  |  Fax 977 1 4410385*
>
> *
>
>
>
>
> On Sun, Nov 25, 2012 at 2:07 AM, Per Westerlund <p1 at westerlund.se> wrote:
>
>> Begin with replacing 'apply-groups [ node0 node1 ];' with 'apply-groups
>> "${NODE}";', the idea is that the two nodes should have different
>> configurations. And while you are making changes, move the section on
>> "services" from "groups node0" to the global configuration, else it will
>> only work when you are connecting to node0, not node1.
>>
>> /Per Westerlund
>>
>>
>> 24 nov 2012 kl. 18:43 skrev Bikash Bhattarai:
>>
>> > Dear all,
>> >
>> > I have just configured two SRX 240 in clustering. One firewall is
>> working
>> > as primary and another is working as secondary. When primary router wan
>> > interface fails the secondary router becomes primary. But after
>> fail-over
>> > network becomes unreachable even from LAN side.
>> >
>> > I have attached the whole configuration.I have configured as per Juniper
>> > documentation. It will be very helpful if anyone point me if I am
>> missing
>> > something.
>> >
>> > Regards,
>> > Bikash Bhattarai | Dristi Tech (P.) Ltd | +977 9851039710 |
>> > www.dristi.com.np
>> > Lazimpat, Kathmandu |Tel  977 1 4427949  |  Fax 977 1 4410385*
>> >
>> > *
>> > <Cluster-Config.txt>_______________________________________________
>> > juniper-nsp mailing list juniper-nsp at puck.nether.net
>> > https://puck.nether.net/mailman/listinfo/juniper-nsp
>>
>>
>
>