[j-nsp] About Juniper IDP 8200 OS update

[Md. Jahangir Hossain]

Thnaks a lot atilf for your valued information.








________________________________
 From: Atif Saleem <malik.atif.saleem at gmail.com>
To: Md. Jahangir Hossain <jrjahangir at yahoo.com> 
Cc: "juniper-nsp at puck.nether.net" <juniper-nsp at puck.nether.net> 
Sent: Monday, October 1, 2012 9:28 AM
Subject: Re: [j-nsp] About Juniper IDP 8200 OS update
 

Hi Jahangir,
 I recently up-graded the IDP OS to 5.1r3 and it did up-grade without any problem. But I used the OS file with shell script (.sh file) as shown below instead of .iso file. You can download it from Juniper website (I suppose you are Juniper partner or customer and have access to download as well as to KB) as it is easy and recommended.

sensor_5_1r3.sh 

You need to make sure that you transfer the above file to "/tmp" of the IDP after doing cheksum and by using either WinScp or FTP in binary mode or file gets corrupted while copying and gives error while up-grading. You can google how to transfer/copy files using WinScp/FTP in binary mode.

After up-grade to 5.1r3 it looked like below.


IDP01 ~]# scio getsystem
Product Name:  NS-IDP-8200
Serial Number:  xxxxxxxxxx
Software Version:  5.1.139197
IDP Mode:  transparent
HA Mode:  Enabled
Detector Version:  5.1.110110809
Software License:   Permanent
Software Expiration Date:   never

Let me give you the steps to up-grade as well, just as a reference.


1. When you transfer the .sh file to the IDP via WinScp make
sure that in TRANSFER SETTING you make it BINARY.
We were facing the error of md5 checksum. We resolved it
by the following KB.
http://kb.juniper.net/InfoCenter/index?page=content&id=KB22668&actp=search&viewlocale=en_US&searchid=1346704354266
2. Open the CLI either SSH (the device may lose connection
during the reboot) or Console access (console is much better option).
3. Run the command
# sh sensor_5_1r3.sh
 
This starts the upgrade process after which it would be
rebooted and may take up to 30 minutes. In case you are have opened an SSH connection, you may initiate a
continuous ping to the device so as to when the device comes up.
 
4. After the upgrade, open the ACM and then click on
ACM--> View/Apply Current configuration and apply these changes.
To run the ACM do "https" access
to the device. 
<https://sensorIPaddress>
On the ACM, click save and apply configuration.
 Refer to release notes of 5.1R3
 <http://www.juniper.net/techpubs/en_US/idp5.1/information-products/topic-collections/idp-5-1-r3-release-notes.pdf>
4. Open up
the NSM right-click the device and Adjust OS version
If you are using NSM and managing the IDP from NSM then NSM version needs to be compatible with 5.1R3. 
Also, if you are using a very old detector engine version then you may need to update
the detector engine. Please refer to KB9773 How to update the detector version on IDP. The
link for the same is as follows:
http://kb.juniper.net/InfoCenter/index?page=content&id=KB9773&actp=search&viewlocale=en_US&searchid=1336101017378
Best of luck!

Atif



On Sun, Sep 30, 2012 at 5:52 PM, Md. Jahangir Hossain <jrjahangir at yahoo.com> wrote:
> Dear friend;
>
>
> Wishes all are fine.
>  
> I need your suggestion about update of  Juniper IDP 8200 OS.
>  
> My current sensor versions is :
>  
> [root at localhost ~]# cat /usr/idp/device/doc/VERSION
> 4.2.112811
>  
> And want to update sensor_5_1r3.iso
>  
> I burn this iso into usb or cdrom and try to install then get a message
> as like “unable to find Kicstart file “
>  
>  
> Can anyone inform or suggest me what is reason for this or this and how
> I can resolve this problem?
>
>
>
>
> Thanks
>
> jahangir
> _______________________________________________
> juniper-nsp mailing list juniper-nsp at puck.nether.net
> https://puck.nether.net/mailman/listinfo/juniper-nsp



-- 
Atif