[j-nsp] Best device to fit for a project

Ben Dale bdale at comlinx.com.au
Tue Apr 1 18:40:55 EDT 2014


Check out AutoVPN as well:

http://www.juniper.net/techpubs/en_US/junos12.1x44/topics/concept/security-autovpn-spoke-authentication-understanding.html

It's hub-and-spoke (as opposed to full-mesh) and a little simpler than GDOI, but you do take the overhead of having to managing PKI across your fleet.

Ben

On 1 Apr 2014, at 6:17 pm, Per Westerlund <p1 at westerlund.se> wrote:

> Another possibility is a cluster of units to take care of the dual PSU requirement.
> 
> For the low end you can mount 2 SRX100 in a 1U tray, and make them a cluster. Will not handle 100Mbps IPsec, but will do 10 Mbps easily, perhaps 50 Mbps depending on how you count and configure (50 bidir is actually 100 in processing power etc). None of the branch SRX have crypto chip, all IPsec is done in CPU, have to watch that.
> 
> Clustered 220/240 would take care of dual PSU for 100 Mbps IPsec, but unfortunately two boxes.
> 
> I don’t have pricing available and don’t run any of these myself, but what about a small MX5 (or similar) with service-card (MS-MIC) for the hub site? It claims throughput of 9Gbps. Would that fit the bill instead of the bigger SRX boxes?
> 
> /Per
> 
> PS: With plain IPsec, no internet tunnel requirement, and SRX everywhere, you can use GDOI (Group VPN, Cisco: GET VPN), but unfortunately that does not work with clusters. Can’t have both right now, sorry. Saves lots of problems managing pre-shared keys etc.
> 
> 1 apr 2014 kl. 09:36 skrev Ben Dale <bdale at comlinx.com.au>:
> 
>> SRX550 is pretty much your only option in the branch if you require dual power supply, but is in every other way overspecced (and thus priced) for the remainder of your branch requirements.  If you can do without the RPS, then I'd go with either an SRX220 or 240, which will easily handle the remainder of your requirements.
>> 
>> Are you sure you want 7-10GBps of IPSEC?  I'm not sure what market you're in, but I don't imagine a 10Gbps WAN port is particularly cheap from your carrier (since you list price as being important).  
>> 
>> If you absolutely need this much crypto though, then you'll be looking at somewhere between an SRX650 and an SRX1400 plus appropriate 10G XPM/IOC.
>> 
>> As for scalability - no issues - the 650 will support up to 3,000 tunnels and the 1400 was good for about 15,000 last time I looked - it's probably gotten better since then.
>> 
>> Ben
>> 
>> On 1 Apr 2014, at 4:37 pm, R S <dim0sal at hotmail.com> wrote:
>> 
>>> For a project (70 branch offices and 2 Headquarters connected in an hub&spoke topology with IPSEC over MPLS among branch and HQ) I’m looking for the best device which cover the following items:
>>> 
>>> Branch:
>>> Single device 
>>> At least two Ethernet interfaces (WAN/LAN)
>>> Ipsec supporting 10-50-100 Mbs
>>> Routing protocols such as BGP-OSPF
>>> NAT
>>> Redundant power supply (some site not but in principle I need it)
>>> 
>>> HeadQuarter:
>>> Single device with XE intf 
>>> At least two Ethernet interfaces (WAN/LAN)
>>> IPSEC supporting up to 7-10 Gbs of IPSEC (the sum of branches)
>>> Routing protocols such as BGP-OSPF
>>> NAT
>>> Redundant power supply
>>> 
>>> Firewall is not needed, MPLS will be runned by the carrier, the devices and IPSEC are on-top of MPLS.
>>> I’m looking for the best solution in terms of scalability and price (very important).
>>> 
>>> Also any advice with experience for the decision is appreciated.
>>> 
>>> Regards
>>> 		 	   		  
>>> _______________________________________________
>>> juniper-nsp mailing list juniper-nsp at puck.nether.net
>>> https://puck.nether.net/mailman/listinfo/juniper-nsp
>> 
>> 
>> _______________________________________________
>> juniper-nsp mailing list juniper-nsp at puck.nether.net
>> https://puck.nether.net/mailman/listinfo/juniper-nsp
> 




More information about the juniper-nsp mailing list