[j-nsp] Trouble with just one IPSec tunnel among many

[Jonathan Call]

A google of this error message directed me to a blog: (http://thomaspollet.blogspot.com/) that discusses how SA can exist in the management plane but not in the data plane. When I ran request pfe execute command "show usp ipsec sa" target fwdd  my st0.142 interface is not listed. 

I've already tried deleting and committing the IPSec settings so I may be forced to do a commit full or a reboot. Clearing the ike and ipsec security-associations gets rid of the settings but the VPN never recovers until remove and commit the SRX B VPN settings again.

Jonathan

________________________________________
From: juniper-nsp <juniper-nsp-bounces at puck.nether.net> on behalf of Jonathan Call <lordsith49 at hotmail.com>
Sent: Wednesday, November 18, 2015 9:19 AM
To: Stefan Fouant
Cc: juniper-nsp at puck.nether.net
Subject: Re: [j-nsp] Trouble with just one IPSec tunnel among many

I found this in the traceoptions I collected from SRX A: http://pastebin.com/Kk0gSzaD

So the tunnel is there, but its not there. That explains the lack of ESP packets on that side.

Jonathan

From: Stefan Fouant <sfouant at shortestpathfirst.net>
Sent: Tuesday, November 17, 2015 8:08 PM
To: Jonathan Call
Cc: juniper-nsp at puck.nether.net
Subject: Re: [j-nsp] Trouble with just one IPSec tunnel among many


Have you tried debugging under [edit security flow traceoptions] yet? There is a wealth of information in there using the flag 'basic-datapath' that may help you.

Stefan Fouant
JNCIE-SEC, JNCIE-SP, JNCIE-ENT, JNCI
m (703) 625-6243

On Nov 17, 2015, at 9:42 PM, Jonathan Call <lordsith49 at hotmail.com> wrote:


I have an SRX250 (SRX A) and an SRX240h2  (SRX B) connected via a PSK IPSec tunnel. They both have multiple IPSec tunnels configured to other SRX devices on our network. Recently the tunnel between the two stopped passing traffic. Both IKE and IPSec  security association were UP on both sides. (show security ike security-association  and show security ipsec security-association) If I pinged from SRX A to something on SRX B I would see the echo request come into SRX B and the echo reply go out. On SRX A  I would only see the outbound packet flow with no response. When I would ping from SRX B to SRX A, SRX A acted as if nothing was happening at all. I ran a traceoptions to capture the ICMP traffic from SRX A to SRX B. SRX A looked like it was sending the traffic  out the tunnel interface but had no reply content. The tracefile on SRX B was completely empty.

After confirming there was nothing abnormal in the routing tables on both of them I tried clearing the IKE and IPSec sessions to rebuild the VPN. Both Phase 1 IKE and Phase 2 IKE came back up but now ping fails in both directions. When I look at the 'show  security ipsec statistics index' information on each side SRX B shows some ESP packets being encrypted and decrypted but not very many. The SRX A ESP statistics are all zeros.

Restarting ipsec key management seems a bit extreme since it will take out all of the other IPSec sessions. Is there some other troubleshooting I can try before I resort to that?

Thank you,

Jonathan



_______________________________________________
juniper-nsp mailing list juniper-nsp at puck.nether.net
https://puck.nether.net/mailman/listinfo/juniper-nsp

_______________________________________________
juniper-nsp mailing list juniper-nsp at puck.nether.net
https://puck.nether.net/mailman/listinfo/juniper-nsp