[j-nsp] Recommended firmware for QFX5100-48T

[Dale Shaw]

Hi all,

On 11 Oct 2016 6:23 AM, "Graham Brown" <juniper-nsp at grahambrown.info> wrote:
>
> Hi Paul,
>
> Correct, just use 'replace pattern xe-0/0/0 with ge-0/0/0' etc and you
> should be fine.

I don't think that's how it works on qfx5100-48**T**

It's more like copper based EX, where the interfaces are configured as
ge-x/x/x even if they're plugged into something capable of only 10 or
100BASE-T operation.

I seem to recall that there is a trick to making it work that involves
autoneg but I'm currently using a tiny screen and an imaginary keyboard so
digging up the details isn't possible right now.

I'm certain that JTAC could help but I'll try to find something when I'm
properly online.

Cheers,
Dale

> On 11 October 2016 at 07:05, Paul S. <contact at winterei.se> wrote:
>
> > Hi Joel,
> >
> > Thanks for replying.
> >
> > What are the steps to configure the ports as "ge." Do I just get rid of
xe
> > from the config and replace it with ge for that port, that's all?
> >
> >
> > On 10/11/2016 12:21 AM, joel jaeggli wrote:
> >
> >> On 10/10/16 7:34 AM, Paul S. wrote:
> >>
> >>> Hi folks,
> >>>
> >>> Are everyone running the JTAC recommended 14.1X53-D35.3 or have you
> >>> found better stability at some newer revision?
> >>>
> >>> My problem is that the "tri state" 10g ports (copper) don't seem to
> >>> want to run at anything less than 10g. It links up when connected to a
> >>> 1g device, but still claims that the port is operating in 10g mode.
> >>>
> >>> The biggest issue I have is that if I assign a /30 to the p2p
> >>> interfaces (between the qfx and any copper 1g device), my p2p latency
> >>> is somewhere from 10 to 40ms.
> >>>
> >>> I asked around to see if there's any way to force the ports into 1g
> >>> mode, but the "speed" knob is missing. I deliberately turned on
> >>> auto-negotiation, does not seem to help.
> >>>
> >>> 802.3ad LAGs created using any of these links also claim to have
> >>> speeds of 20g/40g when there's in reality only 4g of capacity.
> >>>
> >>> Can someone hit me with a clue stick? Thanks!
> >>>
> >> I presume that you're specifing the port config as ge-0/0/foo rather
> >> than xe-0/0/foo
> >>
> >> joel@ show interfaces ge-0/0/46
> >> Physical interface: ge-0/0/46, Enabled, Physical link is Up
> >>    Interface index: 701, SNMP ifIndex: 616
> >>    Description:
> >>    Link-level type: Ethernet, MTU: 1514, Speed: 1000mbps, BPDU Error:
> >> None, MAC-REWRITE Error: None, Loopback: Disabled, Source filtering:
> >> Disabled, Flow control: Disabled, Auto-negotiation: Enabled,
> >>    Remote fault: Online, Media type: Copper
> >>    Device flags   : Present Running
> >>    Interface flags: SNMP-Traps Internal: 0x4000
> >>    Link flags     : None
> >>    CoS queues     : 12 supported, 12 maximum usable queues
> >>    Current address:
> >>    Last flapped   : 2016-08-26 03:31:56 UTC (6w3d 19:46 ago)
> >>    Input rate     : 0 bps (0 pps)
> >>    Output rate    : 0 bps (0 pps)
> >>    Active alarms  : None
> >>    Active defects : None
> >>    Interface transmit statistics: Disabled
> >>
> >>    Logical interface ge-0/0/46.0 (Index 563) (SNMP ifIndex 617)
> >>      Flags: SNMP-Traps 0x4004000 Encapsulation: ENET2
> >>      Input packets : 146287
> >>      Output packets: 292513
> >>      Protocol inet, MTU: 1500
> >>        Flags: Sendbcast-pkt-to-re
> >>        Addresses, Flags: Is-Preferred Is-Primary
> >>          Destination:
> >>
> >> joel@> show chassis hardware
> >> Hardware inventory:
> >> Item             Version  Part number  Serial number     Description
> >> Chassis                                                 QFX5100-48S-6Q
> >> Pseudo CB 0
> >> Routing Engine 0          BUILTIN      BUILTIN           QFX Routing
> >> Engine
> >> FPC 0            REV 05
 QFX5100-48S-6Q
> >>
> >>      Xcvr 46               NON-JNPR          SFP-T
> >>
> >> joel@> show version
> >> fpc0:
> >> ------------------------------------------------------------
> >> --------------
> >> Hostname:
> >> Model: qfx5100-48s-6q
> >> JUNOS Base OS Software Suite [13.2X51-D38]