[rbak-nsp] rate-limit

[Dinesh]

Rule of thumb is

burst = 1.5 X rate

can you try changing burst to 1500 and try ?

Regards
Dinesh



On Thu, May 28, 2009 at 12:13 PM, Илья Савин <savin at orn.ru> wrote:

> Blake, thanks for your reply.
>
> My SmartEdge 100 does not have "show card 2" command :(
> "show qos policy" display this:
>
> [local]Redback#sh qos policy
> Policy-Name                Type     Grid    Qs Slots  Ports  Bound  DnLd
> Status
> inet                       metering 6       0  1      1      out
> pinet                      police   7       0  1      1      in
>
> Total policy map: 2
>
> There is same result if I set up rates locally (not using radius).
>
> Here is a full config (local authorization, without radius):
>
> [local]Redback#sh conf
> Building configuration...
>
> Current configuration:
> !
> !  Configuration last changed by user '<NO USER>' at Thu May 28 22:58:38
> 2009
> !
> !
> !
> !
> !
> !
> no service multiple-contexts
> !
> !
> !
>  software license
>  subscriber active 2000 encrypted 1 $1$***************
> !
> !
>
>
> context local
> !
>  no ip domain-lookup
> !
>  interface outer
>  ip address 80.76.176.44/28
> !
>  interface pool multibind
>  ip address 217.174.10.1/24
>  ip pool 217.174.10.0/24
>  logging console
> !
>  policy access-list SERVICE_out
>  seq 10 permit ip any any class SERVICE1
> !
>  enable encrypted 1 $1$........*****************
> !
>  aaa authentication administrator local
> !
>  administrator root encrypted 1 $1$........********************
> !
> !
>  subscriber default
>   ip address pool
>   qos policy policing pinet
>   qos policy metering inet
>   access-line rate out
>   access-line rate in
> !
>  subscriber name ili4test
>   password test111
>   ip address 217.174.10.100
>   access-line rate out
>   access-line rate in
> !
>  ip route 0.0.0.0/0 80.76.176.33
>  service ssh server
>  service telnet server
> !
>
>
> !
> ! ** End Context **
>  logging tdm console
>  logging active
>  logging standby short
> !
> !
> !
> qos policy inet metering radius-guided
>  rate 1000 burst 100
>  access-group SERVICE_out local
>  class SERVICE1
> !
> qos policy pinet policing radius-guided
>  rate 1000 burst 100
>  access-group SERVICE_out local
>  class SERVICE1
> !
> !
> port ethernet 1/1
> ! XCRP management port on slot 1
>  medium speed 100 duplex full
>  no shutdown
> !
> card carrier 2
> !
> port ethernet 2/1
>  description test21
>  no shutdown
>  encapsulation dot1q
>  bind interface outer local
> !
> port ethernet 2/2
>  no shutdown
>  encapsulation dot1q
>  dot1q pvc 1016 encapsulation pppoe
>  bind authentication chap context local
> !
>  no timeout session idle
> !
> no service console-break
> !
> service crash-dump-dram
> !
> no service auto-system-recovery
> !
> end
>
>
> "show qos circuit detail" displays rate 1000 kbit/s:
> [local]Redback#sh qos circuit detail
> Circuit: 2/2 vlan-id 1016 pppoe 67
> ----------------------------------------------------------
>
> Policy Name       : pinet
> Policy Type       : policing
> Hierarchical Type : None
> Rate              : 1000              Rate Source       : local
> Burst             : 100               Excess Burst      :
> Class mapping     : 1-->0, 2-->0, 3-->0, 4-->0, 5-->0, 6-->0, 7-->0, 8-->0
>
> Policy Name       : inet
> Policy Type       : metering
> Hierarchical Type : None
> Rate              : 1000              Rate Source       : local
> Burst             : 100               Excess Burst      :
> Class mapping     : 1-->0, 2-->0, 3-->0, 4-->0, 5-->0, 6-->0, 7-->0, 8-->0
>
> But actual speed is ~4 kb/s.
> When I remove rate limit actual speed raises up to 100 Mbit/s.
>
> _______________________________________________
> redback-nsp mailing list
> redback-nsp at puck.nether.net
> https://puck.nether.net/mailman/listinfo/redback-nsp
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://puck.nether.net/pipermail/redback-nsp/attachments/20090609/a7ea98fa/attachment.html>