[VoiceOps] as5350 incoming calls failing which have blocked callerid

Blair Harrison blair at fx.net.nz
Thu Sep 9 23:57:22 EDT 2010


So the resolution for this turned out to be the command

 incoming called-number .

on the first pots dial peer as follows -

!
dial-peer voice 1 pots
 destination-pattern T
 translate-outgoing calling 150
 incoming called-number .
 direct-inward-dial
 port 3/0:D
!

Really weird, but this works fine now, just wanted to document my resolution
for anyone else who might be searching the archives :)

Cheers,
Blair

On 26/08/10 22:20, Blair Harrison wrote:
> Hi Guys,
> 
> Have just upgraded one of our PSTN gateways from an old as5300 to a new
> as5350xm. Have run into an issue whereby incoming calls from PSTN which
> have callerID blocked won't complete, and just seem to get dropped on the
> floor.
> 
> I get the following debug output when I make a call from callerid blocked
> number to the gateway - seems odd because the only references I can find
> to this error message are for outgoing calls.. Of note is the Plan / type
> which are Unknown, and the drop cause.
> 
> Cause i = 0x809C - Invalid number format (incomplete number)
> 
> 
> 00124: Aug 26 19:24:54.621 NZST: ISDN Se3/0:15 Q931: RX <- SETUP pd = 8 
> callref = 0x01FF
> 	Sending Complete
> 	Bearer Capability i = 0x9090A3
> 		Standard = CCITT
> 		Transfer Capability = 3.1kHz Audio
> 		Transfer Mode = Circuit
> 		Transfer Rate = 64 kbit/s
>         Channel ID i = 0xA18381
> 		Preferred, Channel 1
> 	Progress Ind i = 0x8283 - Origination address is non-ISDN
> 	Date/Time i = 0x0A081A1318
> 		Date (dd-mm-yr)   = 10-08-26
> 		Time (hr:mnt:sec) = 19:24:52
> 	Signal i = 0x40 - Alerting on - pattern 0
> 	Calling Party Number i = 0x00A3, N/A
> 		Plan:Unknown, Type:Unknown
> 	Called Party Number i = 0x80, '4987770'
> 		Plan:Unknown, Type:Unknown
> 000125: Aug 26 19:24:54.621 NZST: ISDN Se3/0:15 Q931: Received SETUP 
> callref = 0x81FF callID = 0x0017 switch = primary-net5 interface = User
> 000126: Aug 26 19:24:54.621 NZST: ISDN Se3/0:15 Q931: TX -> RELEASE_COMP
> pd = 8  callref = 0x81FF
> 	Cause i = 0x809C - Invalid number format (incomplete number)
> 000127: Aug 26 19:25:04.058 NZST: %CALLTRKR-6-CALL_RECORD: ct_hndl=25,
> service=None, origin=Answer, category=SyncData, DS0
> slot/port/ds1/chan=3/0/0/0, called=4987770, calling=(n/a), resource
> slot/port=(n/a)/(n/a), userid=(n/a), ip=0.0.0.0, account id=(n/a),
> setup=08/26/2010 19:24:53, conn=0.00, phys=0.00, service=0.00,
> authen=0.00, init-rx/tx b-rate=0/0, rx/tx chars=0/0, charged units=0,
> time=0.01, disc subsys=ISDN, disc code=0x1C, disc text=Invalid number
> format (incomplete number), sig type=Unknwn
> 
> Anyone run into this kind of thing before and have any ideas how I might
> configure the box so that these calls complete?
> 
> Cheers,
> Blair
> 
> 
> _______________________________________________
> VoiceOps mailing list
> VoiceOps at voiceops.org
> https://puck.nether.net/mailman/listinfo/voiceops


-- 
Regards,
Blair Harrison
FX Networks

e: blair at fx.net.nz
ddi: 04 498 7770
noc: 0800 65 65 38


More information about the VoiceOps mailing list