<HTML>
<HEAD>
<TITLE>Re: [VoiceOps] T38 over Sip</TITLE>
</HEAD>
<BODY>
<FONT FACE="Calibri, Verdana, Helvetica, Arial"><SPAN STYLE='font-size:11pt'>We are only experiencing problems when trying to send multi page faxes, when sending single page faxes it completes successfully.<BR>
<BR>
Please see the attached sniffer traces, they include calls with both single page and multipage faxes over T.38 with ecm disabled and the G711ulaw<BR>
<BR>
It would seem that no data is transmitted after the MPS message<BR>
<BR>
Pleasee see below the fax configuration<BR>
<BR>
<BR>
voice service voip <BR>
fax protocol t38 ls-redundancy 0 hs-redundancy 0 fallback none<BR>
sip<BR>
!<BR>
!<BR>
voice class codec 1<BR>
codec preference 1 g711ulaw<BR>
<BR>
dial-peer voice 1 voip<BR>
description sip fax test<BR>
translation-profile outgoing voip<BR>
destination-pattern 0T<BR>
voice-class codec 1<BR>
session protocol sipv2<BR>
session target ipv4:192.168.0.14<BR>
incoming called-number 0873514633<BR>
fax-relay ecm disable<BR>
fax protocol t38 nse force ls-redundancy 0 hs-redundancy 0 fallback pass-through g711ulaw<BR>
!<BR>
dial-peer voice 2 pots<BR>
tone ringback alert-no-PI<BR>
destination-pattern 0873514633<BR>
direct-inward-dial<BR>
port 6/0:D<BR>
forward-digits all<BR>
!<BR>
<BR>
<BR>
Looking at the trace I'm concerned about the t38:t30- No-signal messages<BR>
<BR>
<BR>
On 2009/08/28 6:13 PM, &quot;Lee Riemer&quot; &lt;<a href="lriemer@bestline.net">lriemer@bestline.net</a>&gt; wrote:<BR>
<BR>
</SPAN></FONT><BLOCKQUOTE><FONT FACE="Calibri, Verdana, Helvetica, Arial"><SPAN STYLE='font-size:11pt'>Next time you include a capture, don't include your telnet session where we can see you log in. &nbsp;A simple &quot;port 5060&quot; when you start the capture will prevent this.<BR>
<BR>
Anyways, if you don't see something like this:<BR>
<BR>
m=image 16002 udptl t38<BR>
a=T38FaxVersion:0<BR>
a=T38FaxRateManagement:transferredTCF<BR>
a=T38FaxFillBitRemoval:0<BR>
a=T38FaxTranscodingMMR:0<BR>
a=T38FaxTranscodingJBIG:0<BR>
a=T38MaxBitRate:14400<BR>
a=T38FaxUdpEC:t38UDPFEC<BR>
a=T38FaxMaxBuffer:200<BR>
a=T38FaxMaxDatagram:72<BR>
<BR>
in the SDP section, T38 is not attempting to kick in.<BR>
<BR>
Lee Riemer - Director IP Voice<BR>
Bestline Communications, L.P.<BR>
512.328.9095 Voice<BR>
512.328.0038 Fax<BR>
<BR>
Junaid Hattia wrote: <BR>
</SPAN></FONT><BLOCKQUOTE><FONT FACE="Calibri, Verdana, Helvetica, Arial"><SPAN STYLE='font-size:11pt'> <BR>
So basically I cannot fax...attached is the wireshark trace<BR>
<BR>
<BR>
On 2009/08/28 1:29 PM, &quot;Alex Balashov&quot; &lt;<a href="abalashov@evaristesys.com">abalashov@evaristesys.com</a>&gt; &lt;<a href="mailto:abalashov@evaristesys.com">mailto:abalashov@evaristesys.com</a>&gt; &nbsp;wrote:<BR>
<BR>
&nbsp;&nbsp;<BR>
&nbsp;<BR>
</SPAN></FONT><BLOCKQUOTE><FONT FACE="Calibri, Verdana, Helvetica, Arial"><SPAN STYLE='font-size:11pt'> <BR>
There are many things that could be wrong there. &nbsp;Problem description is<BR>
not sufficient.<BR>
<BR>
Junaid Hattia wrote:<BR>
<BR>
&nbsp;&nbsp;&nbsp;&nbsp;<BR>
&nbsp;<BR>
</SPAN></FONT><BLOCKQUOTE><FONT FACE="Calibri, Verdana, Helvetica, Arial"><SPAN STYLE='font-size:11pt'> <BR>
Howdy<BR>
<BR>
Ok so im trying to t38 over sip working with no luck<BR>
<BR>
My test lab is as follows:<BR>
<BR>
Pangea box connecting to a AS5400 via PRI, which then traverses an Acme<BR>
Session director, broadsoft and then exits via PGW(SS7)<BR>
<BR>
The sniffer capture says &sup3;failure to train&sup2;<BR>
<BR>
<BR>
Any ideas?<BR>
<BR>
--<BR>
&nbsp;junaid<BR>
<BR>
<BR>
<BR>
<BR>
<BR>
Please note: This email and its content are subject to the disclaimer as<BR>
displayed at the following link<BR>
<a href="http://www.is.co.za/legal/E-mail+Confidentiality+Notice+and+Disclaimer.htm">http://www.is.co.za/legal/E-mail+Confidentiality+Notice+and+Disclaimer.htm</a>.<BR>
Should you not have Web access, send an email to<BR>
<a href="mailto:disclaimers@is.co.za">mailto:disclaimers@is.co.za</a> and a copy will be sent to you.<BR>
<BR>
<BR>
------------------------------------------------------------------------<BR>
<BR>
_______________________________________________<BR>
VoiceOps mailing list<BR>
<a href="VoiceOps@voiceops.org">VoiceOps@voiceops.org</a><BR>
<a href="https://puck.nether.net/mailman/listinfo/voiceops">https://puck.nether.net/mailman/listinfo/voiceops</a><BR>
&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;<BR>
&nbsp;<BR>
</SPAN></FONT></BLOCKQUOTE><FONT FACE="Calibri, Verdana, Helvetica, Arial"><SPAN STYLE='font-size:11pt'> <BR>
</SPAN></FONT></BLOCKQUOTE><FONT FACE="Calibri, Verdana, Helvetica, Arial"><SPAN STYLE='font-size:11pt'> <BR>
<BR>
<BR>
Please note: This email and its content are subject to the disclaimer as displayed at the following link <a href="http://www.is.co.za/legal/E-mail+Confidentiality+Notice+and+Disclaimer.htm">http://www.is.co.za/legal/E-mail+Confidentiality+Notice+and+Disclaimer.htm</a>. Should you not have Web access, send a mail to <a href="disclaimers@is.co.za">disclaimers@is.co.za</a> and a copy will be emailed to you.<BR>
&nbsp;<BR>
<BR>
<HR ALIGN=CENTER SIZE="4" WIDTH="90%"><BR>
_______________________________________________<BR>
VoiceOps mailing list<BR>
<a href="VoiceOps@voiceops.org">VoiceOps@voiceops.org</a><BR>
<a href="https://puck.nether.net/mailman/listinfo/voiceops">https://puck.nether.net/mailman/listinfo/voiceops</a><BR>
</SPAN></FONT></BLOCKQUOTE><FONT FACE="Calibri, Verdana, Helvetica, Arial"><SPAN STYLE='font-size:11pt'><BR>
</SPAN></FONT></BLOCKQUOTE>

<FONT face=Verdana size=1>Please note: This email and its content are 
subject to the disclaimer as displayed at the following link </FONT><A 
href="http://www.is.co.za/legal/E-mail+Confidentiality+Notice+and+Disclaimer.htm"><FONT 
face=Verdana 
size=1>http://www.is.co.za/legal/E-mail+Confidentiality+Notice+and+Disclaimer.htm</FONT></A><FONT 
face=Verdana size=1>. Should you not have Web access, send an email to </FONT><A 
href="mailto:disclaimers@is.co.za"><FONT face=Verdana 
size=1>mailto:disclaimers@is.co.za</FONT></A><FONT face=Verdana size=1> and a 
copy will be sent to you.</FONT> 
</BODY>
</HTML>