RE: Odd T1 problem

From: Sean Herr (sean@ync.net)
Date: Thu Dec 27 2001 - 00:03:29 EST


I had a similar problem a few weeks ago, turned out my colo provider had
a mux issue, Ameritech changed us to a different slot on the T3 we were
coming in on and it corrected the problem. Ameritech was able to run
clean to the CSU during testing but could not bring the loop back down,
obviously they were seeing the loop in the mux.

Sean Herr
Director of Technical Operations
@YourNET Connection, Inc.
http://www.ync.net
847-524-3900

-----Original Message-----
From: jlewis@lewis.org [mailto:jlewis@lewis.org]
Sent: Wednesday, December 26, 2001 10:46 PM
To: James S. Lertora III
Cc: cisco-nsp@puck.nether.net
Subject: Re: Odd T1 problem

They claim they've verified it (ESF/B8ZS) on all their gear this circuit
goes through.

On Wed, 26 Dec 2001, James S. Lertora III wrote:

> Sounds to me like a framing issue with the Telco. I'll bet the problem
> disapears and Bell says they found nothing wrong. (he he)
> ----- Original Message -----
> From: <jlewis@lewis.org>
> To: <cisco-nsp@puck.nether.net>
> Sent: Wednesday, December 26, 2001 4:19 PM
> Subject: Re: Odd T1 problem
>
>
> > One more thing to add...
> >
> > If a loopback plug is inserted in the smart jack at either the A or
Z end,
> > the router at the other end sees the loop and can run patterns (all
0's,
> > alternating 0's/1's, all 1's) across the loop. Remove the loopback
plug
> > and plug the routers back in, and the line proto starts flapping
again.
> > Trun off keepalives, and the protocol stays up, but neither router
sees
> > packets sent by the other.
> >
> > Bell is supposed to be having someone make sure the framing/line
coding is
> > properly set in the DACS and any other equipment the circuit goes
through.
> >
> > On Wed, 26 Dec 2001 jlewis@lewis.org wrote:
> >
> > > I've got an odd T1 problem I've been unable to solve remotely.
It's a
> > > BellSouth point to point T1 between 2 locations in the same city.
Cisco
> > > 1600 and Digital Link Prelude at the Z end, 2620 with WIC-2T and
Larscom
> > > Access-T's at the A end. All of a sudden, line protocol (we're
using
> > > hdlc) is flapping on both sides. i.e.
> > >
> > > Dec 26 19:13:58: %LINEPROTO-5-UPDOWN: Line protocol on Interface
> > > Serial0/3, changed state to down
> > > Dec 26 19:14:00: %LINEPROTO-5-UPDOWN: Line protocol on Interface
> > > Serial0/3, changed state to up
> > > Dec 26 19:14:28: %LINEPROTO-5-UPDOWN: Line protocol on Interface
> > > Serial0/3, changed state to down
> > > Dec 26 19:14:30: %LINEPROTO-5-UPDOWN: Line protocol on Interface
> > > Serial0/3, changed state to up
> > >
> > > This site is a couple hundred miles away, and though I don't have
anyone
> > > technical there, there is a person able to move wires around. I
had
> them
> > > move the T1 patch cable to another CSU on another WIC-2T port and
it
> kept
> > > doing this...so that eliminates the CSU and WIC port.
> > >
> > > I've had bell loop the circuit towards the A side and towards the
Z
> side,
> > > and have been able to run extended pings with various patterns
across
> each
> > > half of the circuit. When they reconnect the A and Z ends in the
DACS,
> > > line protocol goes back to flapping. Until it failed, this
circuit had
> > > been in use for quite a while, so I don't suspect CSU config
issues.
> > >
> > > All equipment at each end has been power cycled.
> > >
> > > I haven't tried having the remote people replace patch cables, but
I
> > > wouldn't think each half of the circuit would have tested ok if
there
> was
> > > a bad cable.
> > >
> > > Anyone have any idea what this might be? I really don't want to
do it,
> > > but I've run out of ideas other than grabbing enough spare gear to
> replace
> > > everything at each end and driving up there to replace all the
gear and
> > > wiring.
> > >
> > >
> >
> > --
> >
----------------------------------------------------------------------
> > Jon Lewis *jlewis@lewis.org*| I route
> > System Administrator | therefore you are
> > Atlantic Net |
> > _________ http://www.lewis.org/~jlewis/pgp for PGP public
key_________
> >
> >
>

-- 
----------------------------------------------------------------------
 Jon Lewis *jlewis@lewis.org*|  I route
 System Administrator        |  therefore you are
 Atlantic Net                |
_________ http://www.lewis.org/~jlewis/pgp for PGP public key_________



This archive was generated by hypermail 2b29 : Sun Aug 04 2002 - 04:12:58 EDT