[cisco-voip] Calling Name (inbound and outbound) not working on 3640 and NM-HDV-2MFT-T1 48

[William M. Sandiford]

Ok

So I finally got the calling name into the q931 trace as a facility message.  It turns out that Calling name as a facility IE message wasn't supported until 12.3(4)T so I had to upgrade to a newer version of IOS.  That being said.  Now I am seeing the calling name in the trace, but it still isn't making it into the sip message.

Any suggestions?

Bill


00:08:52: ISDN Se3/0:23 Q931: RX <- SETUP pd = 8  callref = 0x03C9 
        Bearer Capability i = 0x8090A2 
                Standard = CCITT 
                Transer Capability = Speech  
                Transfer Mode = Circuit 
                Transfer Rate = 64 kbit/s 
        Channel ID i = 0xA98381 
                Exclusive, Channel 1 
        Facility i = 0x9F8B0100A117020101020100800F43414E444E20444F4D41494E204E41 
                Protocol Profile =  Networking Extensions 
                0xA117020101020100800F43414E444E20444F4D41494E204E41 
                Component = Invoke component 
                        Invoke Id = 1 
                        Operation = CallingName 
                                Name presentation allowed
                                Name = THE NAME 
        Progress Ind i = 0x8283 - Origination address is non-ISDN  
        Calling Party Number i = 0x2183, 'XXXXXX6814' 
                Plan:ISDN, Type:National 
        Called Party Number i = 0xA1, 'XXXXXX2000' 
                Plan:ISDN, Type:National
00:08:52: ISDN Se3/0:23 Q931: TX -> CALL_PROC pd = 8  callref = 0x83C9 
        Channel ID i = 0xA98381 
                Exclusive, Channel 1
00:08:52: ISDN Se3/0:23 Q931: TX -> CONNECT pd = 8  callref = 0x83C9
00:08:52: ISDN Se3/0:23 Q931: RX <- CONNECT_ACK pd = 8  callref = 0x03C9
00:08:56: ISDN Se3/0:23 Q931: RX <- DISCONNECT pd = 8  callref = 0x03C9 
        Cause i = 0x8090 - Normal call clearing
00:08:56: ISDN Se3/0:23 Q931: TX -> RELEASE pd = 8  callref = 0x83C9
00:08:57: ISDN Se3/0:23 Q931: RX <- RELEASE_COMP pd = 8  callref = 0x03C



-----Original Message-----
From: Mark R. Lindsey [mailto:lindsey at e-c-group.com] 
Sent: Tuesday, March 01, 2005 11:29 AM
To: William M. Sandiford
Cc: cisco-voip at puck.nether.net
Subject: Re: [cisco-voip] Calling Name (inbound and outbound) not working on 3640 and NM-HDV-2MFT-T1 48


On Mar 1, 2005, at 11:20 AM, William M. Sandiford wrote:

> So it looks like I'm going to have to go off of mainline and on to T
> in order to get this to work?

I think so. But even in those, we've helped Cisco identify some issues 
--

CSceg80858 -- Remote-Party-ID is formatted wrong/oddly in current 
releases (to be addressed in 12.4)

CSCsa67646 -- SIP "486 Busy Here" messages aren't returned on some 
SIP-PSTN calls

---
Mark R. Lindsey, ECG
+1-229-316-0013 lindsey at e-c-group.com


-- 
No virus found in this incoming message.
Checked by AVG Anti-Virus.
Version: 7.0.300 / Virus Database: 266.5.4 - Release Date: 3/1/2005
 

-- 
No virus found in this outgoing message.
Checked by AVG Anti-Virus.
Version: 7.0.300 / Virus Database: 266.5.4 - Release Date: 3/1/2005