[cisco-voip] Calling Name (inbound and outbound) not
workingon3640 and NM-HDV-2MFT-T1 48, Facility IE
Blomfield, Adam
Adam.Blomfield at sulzer.com
Wed Mar 9 11:44:38 EST 2005
I have a similar setup to this... my gateway is a 3662 running IOS
12.3(11)T3. I had my trunks changed from 5eSS to NI2 last night and I am
now getting calling name delivered into the Facilities IE and can see
this information in a Q931 debug as shown below. The gateway is
connected to CCM via H.323 and I am not trying to configure it so that
the name is passed onto the phone handsets, however I cannot see any way
to get CallManager to looked at the Facility IE on a H.323 gateway. Is
it possible or do I have to migrate to MGCP to get this functionality?
Thanks,
Adam
_________________________________________
Adam Blomfield
WAN Administrator
Information Technology
Sulzer Chemtech USA, Inc.
4019 South Jackson Avenue, Tulsa OK 74107
Tel. +1 918-445-6642, Fax +1 918-446-4701
Cell +1 918-625-1739
E-Mail mailto:adam.blomfield at sulzer.com
Internet http://www.sulzerchemtech.com
_________________________________________
-----Original Message-----
From: cisco-voip-bounces at puck.nether.net
[mailto:cisco-voip-bounces at puck.nether.net] On Behalf Of William M.
Sandiford
Sent: Wednesday, March 02, 2005 9:35 AM
To: cisco-voip at puck.nether.net
Subject: RE: [cisco-voip] Calling Name (inbound and outbound) not
workingon3640 and NM-HDV-2MFT-T1 48, Facility IE
Hello:
Just a quick note for all that were following this thread and that have
helped out, I was able to get the problem totally solved. I'm posting
this for reference / archive purposes in case others have this problem
in the future.
The problem was that my carrier (TELUS) passes the calling name as a
Facility IE as opposed to a Display IE. On my platform (3640), and most
others I presume, calling name by facility IE was not supported until
IOS 12.3(4)T so you will need that or later to make it work (I used
12.3(11)T3). The following configuration items were required in
addition to any other configs that you already have.
Under the serial interface for your T1, in my case int Serial3/0:23
Interface Serial3/0:23
isdn supp-service name calling
isdn outgoing ie facility
no isdn outgoing display-ie
!
Thanks to everyone who pointed me in the right direction for all the
help.
Regards,
Bill
-----Original Message-----
From: William M. Sandiford
Sent: Tuesday, March 01, 2005 4:57 PM
To: Mark R. Lindsey; cisco-voip at puck.nether.net
Subject: RE: [cisco-voip] Calling Name (inbound and outbound) not
working on3640 and NM-HDV-2MFT-T1 48
Ok
So I finally got the calling name into the q931 trace as a facility
message. It turns out that Calling name as a facility IE message wasn't
supported until 12.3(4)T so I had to upgrade to a newer version of IOS.
That being said. Now I am seeing the calling name in the trace, but it
still isn't making it into the sip message.
Any suggestions?
Bill
00:08:52: ISDN Se3/0:23 Q931: RX <- SETUP pd = 8 callref = 0x03C9
Bearer Capability i = 0x8090A2
Standard = CCITT
Transer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA98381
Exclusive, Channel 1
Facility i =
0x9F8B0100A117020101020100800F43414E444E20444F4D41494E204E41
Protocol Profile = Networking Extensions
0xA117020101020100800F43414E444E20444F4D41494E204E41
Component = Invoke component
Invoke Id = 1
Operation = CallingName
Name presentation allowed
Name = THE NAME
Progress Ind i = 0x8283 - Origination address is non-ISDN
Calling Party Number i = 0x2183, 'XXXXXX6814'
Plan:ISDN, Type:National
Called Party Number i = 0xA1, 'XXXXXX2000'
Plan:ISDN, Type:National
00:08:52: ISDN Se3/0:23 Q931: TX -> CALL_PROC pd = 8 callref = 0x83C9
Channel ID i = 0xA98381
Exclusive, Channel 1
00:08:52: ISDN Se3/0:23 Q931: TX -> CONNECT pd = 8 callref = 0x83C9
00:08:52: ISDN Se3/0:23 Q931: RX <- CONNECT_ACK pd = 8 callref = 0x03C9
00:08:56: ISDN Se3/0:23 Q931: RX <- DISCONNECT pd = 8 callref = 0x03C9
Cause i = 0x8090 - Normal call clearing
00:08:56: ISDN Se3/0:23 Q931: TX -> RELEASE pd = 8 callref = 0x83C9
00:08:57: ISDN Se3/0:23 Q931: RX <- RELEASE_COMP pd = 8 callref = 0x03C
-----Original Message-----
From: Mark R. Lindsey [mailto:lindsey at e-c-group.com]
Sent: Tuesday, March 01, 2005 11:29 AM
To: William M. Sandiford
Cc: cisco-voip at puck.nether.net
Subject: Re: [cisco-voip] Calling Name (inbound and outbound) not
working on 3640 and NM-HDV-2MFT-T1 48
On Mar 1, 2005, at 11:20 AM, William M. Sandiford wrote:
> So it looks like I'm going to have to go off of mainline and on to T
> in order to get this to work?
I think so. But even in those, we've helped Cisco identify some issues
--
CSceg80858 -- Remote-Party-ID is formatted wrong/oddly in current
releases (to be addressed in 12.4)
CSCsa67646 -- SIP "486 Busy Here" messages aren't returned on some
SIP-PSTN calls
---
Mark R. Lindsey, ECG
+1-229-316-0013 lindsey at e-c-group.com
--
No virus found in this incoming message.
Checked by AVG Anti-Virus.
Version: 7.0.300 / Virus Database: 266.5.4 - Release Date: 3/1/2005
--
No virus found in this outgoing message.
Checked by AVG Anti-Virus.
Version: 7.0.300 / Virus Database: 266.5.4 - Release Date: 3/1/2005
_______________________________________________
cisco-voip mailing list
cisco-voip at puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-voip
--
No virus found in this incoming message.
Checked by AVG Anti-Virus.
Version: 7.0.300 / Virus Database: 266.5.4 - Release Date: 3/1/2005
--
No virus found in this outgoing message.
Checked by AVG Anti-Virus.
Version: 7.0.300 / Virus Database: 266.5.4 - Release Date: 3/1/2005
_______________________________________________
cisco-voip mailing list
cisco-voip at puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-voip
More information about the cisco-voip
mailing list