[cisco-voip] Dial collection

[Brian Turnbow]

Hi 
yes and with two state dialing , The end users digits a code to access the voip line and receives tone fron the router ( no direct dial in) 
Below is an ISDN setup, and everything looks ok. 
However on the outboud h323 i See  00223366552299443300 as the called number. 
ISDN phones send correct on the pbx, it is only the analog lines that have this problem. 
 
 
*Jun 20 14:59:16.151: ISDN Se0/0/0:15 Q931: RX <- SETUP pd = 8  callref = 0x018E
        Bearer Capability i = 0x9090A3
                Standard = CCITT
                Transer Capability = 3.1kHz Audio
                Transfer Mode = Circuit
                Transfer Rate = 64 kbit/s
        Channel ID i = 0xA98385
                Exclusive, Channel 5
        Progress Ind i = 0x8083 - Origination address is non-ISDN
        Calling Party Number i = 0x0181, '219'
                Plan:ISDN, Type:Unknown
        Low Layer Compat i = 0x9090A3
*Jun 20 14:59:16.159: ISDN Se0/0/0:15 Q931: TX -> SETUP_ACK pd = 8  callref = 0x818E
        Channel ID i = 0xA98385
                Exclusive, Channel 5
*Jun 20 14:59:16.991: ISDN Se0/0/0:15 Q931: RX <- INFORMATION pd = 8  callref = 0x018E
        Called Party Number i = 0x81, '0'
                Plan:ISDN, Type:Unknown
*Jun 20 14:59:17.779: ISDN Se0/0/0:15 Q931: RX <- INFORMATION pd = 8  callref = 0x018E
        Called Party Number i = 0x81, '2'
                Plan:ISDN, Type:Unknown
*Jun 20 14:59:18.495: ISDN Se0/0/0:15 Q931: RX <- INFORMATION pd = 8  callref = 0x018E
        Called Party Number i = 0x81, '3'
                Plan:ISDN, Type:Unknown
*Jun 20 14:59:19.199: ISDN Se0/0/0:15 Q931: RX <- INFORMATION pd = 8  callref = 0x018E
        Called Party Number i = 0x81, '6'
                Plan:ISDN, Type:Unknown
*Jun 20 14:59:19.795: ISDN Se0/0/0:15 Q931: RX <- INFORMATION pd = 8  callref = 0x018E
        Called Party Number i = 0x81, '5'
                Plan:ISDN, Type:Unknown
*Jun 20 14:59:20.387: ISDN Se0/0/0:15 Q931: RX <- INFORMATION pd = 8  callref = 0x018E
        Called Party Number i = 0x81, '2'
                Plan:ISDN, Type:Unknown
*Jun 20 14:59:21.087: ISDN Se0/0/0:15 Q931: RX <- INFORMATION pd = 8  callref = 0x018E
        Called Party Number i = 0x81, '9'
                Plan:ISDN, Type:Unknown
*Jun 20 14:59:21.591: ISDN Se0/0/0:15 Q931: RX <- INFORMATION pd = 8  callref = 0x018E
        Called Party Number i = 0x81, '4'
                Plan:ISDN, Type:Unknown
*Jun 20 14:59:22.391: ISDN Se0/0/0:15 Q931: RX <- INFORMATION pd = 8  callref = 0x018E
        Called Party Number i = 0x81, '3'
                Plan:ISDN, Type:Unknown
*Jun 20 14:59:22.983: ISDN Se0/0/0:15 Q931: RX <- INFORMATION pd = 8  callref = 0x018E
        Called Party Number i = 0x81, '0'
                Plan:ISDN, Type:Unknown
*Jun 20 14:59:27.987: ISDN Se0/0/0:15 Q931: TX -> CALL_PROC pd = 8  callref = 0x818E

interface Serial0/0/0:15
 no ip address
 isdn switch-type primary-net5
 isdn overlap-receiving T302 5000
 isdn network-failure-cause 16
 isdn protocol-emulate network
 isdn incoming-voice voice
 isdn send-alerting
 no cdp enable
 
 
 
thanks
Brian

________________________________

From: Fedorov, Konstantin [mailto:kfedor at amt.ru] 
Sent: martedì 20 giugno 2006 16.54
To: Brian Turnbow; cisco-voip at puck.nether.net
Subject: RE: [cisco-voip] Dial collection



Hi, Brian.

 

ISDN Info - so you PBX send digits over overlap.

 

Whai is you scenario ? Two state dialing ??

 

Can you send a snip  of

Debug isdn q931 

 

And D channel configuration.

-----------------------
Sincerely Yours,
Konstantin Fedorov

________________________________

From: cisco-voip-bounces at puck.nether.net [mailto:cisco-voip-bounces at puck.nether.net] On Behalf Of Brian Turnbow
Sent: Tuesday, June 20, 2006 6:45 PM
To: cisco-voip at puck.nether.net
Subject: [cisco-voip] Dial collection

 

 

Hello all, 

I have a 2821 with a E1 multiflex card connected to a PBX. 
When analog lines of the pbx dial out I receive both the in band dialed digits and isdn info messages from the pbx. 
This causes the router to send out in h323 the incorrect numer . For example  1234 gets sent out as 11223344 
I have been looking for a way to disable the in band digit collection, but have yet to find out how. 
Can any one point me in the right direction ? 

Thanks 
Brian 

-------------- next part --------------
An HTML attachment was scrubbed...
URL: https://puck.nether.net/pipermail/cisco-voip/attachments/20060620/faec72b7/attachment-0001.html