[cisco-voip] clid on fxs ports
Brian Henry
Brian.Henry at apptis.com
Thu Jun 29 07:49:12 EDT 2006
First talk to your provider and let them know that you wish to control the ANI and not them with the Billing Number that is associated with the PRI.
Brian
________________________________
From: cisco-voip-bounces at puck.nether.net on behalf of Anthony Kouloglou
Sent: Thu 6/29/2006 6:19 AM
To: Ryan Ratliff
Cc: cisco-voip at puck-nether.net
Subject: Re: [cisco-voip] clid on fxs ports
Ryan
here is a csim start command from that router
Lon2851#csim start 90030xxxxxxxxxx
csim: called number = 90030xxxxxxxxxx, loop count = 1 ping count = 0
*Jun 29 11:11:08.959: ISDN Se0/2/0:15 Q931: Applying typeplan for sw-type 0x12 is 0x0 0x0, Called num 0030xxxxxxxxxx
*Jun 29 11:11:08.959: ISDN Se0/2/0:15 Q931: TX -> SETUP pd = 8 callref = 0x0164
Bearer Capability i = 0x8090A3
Standard = CCITT
Transfer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA9839E
Exclusive, Channel 30
Called Party Number i = 0x80, '0030xxxxxxxxxx'
Plan:Unknown, Type:Unknown
*Jun 29 11:11:09.103: ISDN Se0/2/0:15 Q931: RX <- SETUP_ACK pd = 8 callref = 0x8164
Channel ID i = 0xA9839E
Exclusive, Channel 30
Progress Ind i = 0x8288 - In-band info or appropriate now available
*Jun 29 11:11:15.555: ISDN Se0/2/0:15 Q931: RX <- ALERTING pd = 8 callref = 0x8164
*Jun 29 11:11:17.839: ISDN Se0/2/0:15 Q931: RX <- CONNECT pd = 8 callref = 0x8164
*Jun 29 11:11:17.839: %ISDN-6-CONNECT: Interface Serial0/2/0:29 is now connected to xxxxxxxxxx N/A
*Jun 29 11:11:17.839: ISDN Se0/2/0:15 Q931: TX -> CONNECT_ACK pd = 8 callref = 0x0164
*Jun 29 11:11:18.391: ISDN Se0/2/0:15 Q931: RX <- DISCONNECT pd = 8 callref = 0x8164
Cause i = 0x8090 - Normal call clearing
Progress Ind i = 0x8288 - In-band info or appropriate now available
*Jun 29 11:11:18.395: ISDN Se0/2/0:15 Q931: call_disc: PI received in disconnect; Postpone sending RELEASE for callid 0x8164.
csim: loop = 1, failed = 0
csim: call attempted = 1, setup failed = 0, tone failed = 1
Lon2851#
I guess there is no Calling party in the setup message.
When there is a call from an ip phone, there is calling party (the extension of the ccm). Of course the POTS provider just shows the number of the PRI to the called party and not the internal extension of the CCM.
But when i make calls from the router ( with csim start) or the fxs (a modem attached there), there is no calling party on the q931setup message and so the provider does not shows anything to the called.
I have tried configuring isdn calling-number etc on the serial 0/2/0:15 but nothing changes. Must i put something there or at the dial-peer pots?
The customer wants this feature desperately!!!
Cheers,
Anthony
Ryan Ratliff wrote:
Do you have a q931 debug showing the outbound call?
-Ryan
On Jun 28, 2006, at 12:03 PM, Anthony Kouloglou wrote:
Hi all,
on a 2851 with one E1 and 4 FXS ports i have configured the voice port
as follows:
voice-port 0/3/2
cptone GB
description xxx
station-id name yyy
station-id number 1234
caller-id enable type 1
there is also these:
voice-port 0/2/0:15
translation-profile incoming TP01
bearer-cap Speech
interface Serial0/2/0:15
no ip address
isdn switch-type primary-net5
isdn incoming-voice voice
no cdp enable
dial-peer voice 10 pots
destination-pattern 9T
port 0/2/0:15
when i call from the analog phone to an ipphone extension internally i
have clid (both name and number) to the ipphone
but when i make calls through the pri, i get "uknown number" to the
external phone that i have called.
Is this ficed somehow?
Cheers
Anthony
_______________________________________________
cisco-voip mailing list
cisco-voip at puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-voip
-------------- next part --------------
An HTML attachment was scrubbed...
URL: https://puck.nether.net/pipermail/cisco-voip/attachments/20060629/a4c9db56/attachment.html
More information about the cisco-voip
mailing list