[cisco-voip] clid on fxs ports

[Fedorov, Konstantin]

Hi,

 

Csim start - how I remember is not supported command.

 

Can you provide debug when you call from actual phone attached to fxs ?

-----------------------
Sincerely Yours,
Konstantin Fedorov

  _____  

From: cisco-voip-bounces at puck.nether.net
[mailto:cisco-voip-bounces at puck.nether.net] On Behalf Of Anthony
Kouloglou
Sent: Thursday, June 29, 2006 2:19 PM
To: Ryan Ratliff
Cc: cisco-voip at puck-nether.net
Subject: Re: [cisco-voip] clid on fxs ports

 

Ryan
here is a csim start command from that router

Lon2851#csim start 90030xxxxxxxxxx
csim: called number = 90030xxxxxxxxxx, loop count = 1 ping count = 0

*Jun 29 11:11:08.959: ISDN Se0/2/0:15 Q931: Applying typeplan for
sw-type 0x12 is 0x0 0x0, Called num 0030xxxxxxxxxx
*Jun 29 11:11:08.959: ISDN Se0/2/0:15 Q931: TX -> SETUP pd = 8  callref
= 0x0164 
        Bearer Capability i = 0x8090A3 
                Standard = CCITT 
                Transfer Capability = Speech  
                Transfer Mode = Circuit 
                Transfer Rate = 64 kbit/s 
        Channel ID i = 0xA9839E 
                Exclusive, Channel 30 
        Called Party Number i = 0x80, '0030xxxxxxxxxx' 
                Plan:Unknown, Type:Unknown
*Jun 29 11:11:09.103: ISDN Se0/2/0:15 Q931: RX <- SETUP_ACK pd = 8
callref = 0x8164 
        Channel ID i = 0xA9839E 
                Exclusive, Channel 30 
        Progress Ind i = 0x8288 - In-band info or appropriate now
available 
*Jun 29 11:11:15.555: ISDN Se0/2/0:15 Q931: RX <- ALERTING pd = 8
callref = 0x8164
*Jun 29 11:11:17.839: ISDN Se0/2/0:15 Q931: RX <- CONNECT pd = 8
callref = 0x8164
*Jun 29 11:11:17.839: %ISDN-6-CONNECT: Interface Serial0/2/0:29 is now
connected to xxxxxxxxxx N/A
*Jun 29 11:11:17.839: ISDN Se0/2/0:15 Q931: TX -> CONNECT_ACK pd = 8
callref = 0x0164
*Jun 29 11:11:18.391: ISDN Se0/2/0:15 Q931: RX <- DISCONNECT pd = 8
callref = 0x8164 
        Cause i = 0x8090 - Normal call clearing 
        Progress Ind i = 0x8288 - In-band info or appropriate now
available 
*Jun 29 11:11:18.395: ISDN Se0/2/0:15 Q931: call_disc: PI received in
disconnect; Postpone sending RELEASE for callid 0x8164.
csim: loop = 1, failed = 0  
csim: call attempted = 1, setup failed = 0, tone failed = 1

Lon2851#

I guess there is no Calling party in the setup message.
When there is a call from an ip phone, there is calling party (the
extension of the ccm). Of course the POTS provider just shows the number
of the PRI to the called party and not the internal extension of the
CCM.
But when i make calls from the router ( with csim start) or the fxs (a
modem attached there), there is no calling party on the q931setup
message and so the provider does not shows anything to the called.
I have tried configuring isdn calling-number etc on the serial 0/2/0:15
but nothing changes. Must i put something there or at the dial-peer
pots?
The customer wants this feature desperately!!!

Cheers,
Anthony
Ryan Ratliff wrote: 

Do you have a q931 debug showing the outbound call? 

-Ryan 

On Jun 28, 2006, at 12:03 PM, Anthony Kouloglou wrote: 

Hi all, 
on a 2851 with one E1 and 4 FXS ports i have configured the voice port 
as follows: 

_______________________________________________ 
cisco-voip mailing list 
cisco-voip at puck.nether.net 
https://puck.nether.net/mailman/listinfo/cisco-voip 

-------------- next part --------------
An HTML attachment was scrubbed...
URL: https://puck.nether.net/pipermail/cisco-voip/attachments/20060630/4344832b/attachment-0001.html