[cisco-voip] h323 gw config
James Grace
jgrace at digitelusa.net
Tue Mar 28 17:43:59 EST 2006
This is what I get
DISC CAUSE CODE FROM OTHER PEER FROM H323 PEER
3 no route to destinatio 4 0
H323 gateway internal event queue:
Events queued 0, free 1, held 1, allocated 1 times, exceed max 0 times
Max serviced 1, Max serviced exceed 0
no dest 0, no buffers 0, call flushes 0
CRV statistics
In use: 0
Max collisions obtaining crv: 0
_____
From: Leetun, Rob [mailto:rleetun at co.boulder.co.us]
Sent: Tuesday, March 28, 2006 4:59 PM
To: James Grace
Subject: RE: [cisco-voip] h323 gw config
That is for four digit dialing inside our network. [1-8]... The last three
dots are any number that starts with a number 1, 2, 3, 4, 5, 6, 7, or 8
_____
From: James Grace [mailto:jgrace at digitelusa.net]
Sent: Tuesday, March 28, 2006 2:48 PM
To: Leetun, Rob
Subject: RE: [cisco-voip] h323 gw config
Thank for the help
The one im confused on is the destination-pattern [1-8] Where or what is
this for when dealing with cm
_____
From: Leetun, Rob [mailto:rleetun at co.boulder.co.us]
Sent: Tuesday, March 28, 2006 4:42 PM
To: James Grace
Subject: RE: [cisco-voip] h323 gw config
Yours could look like this:
dial-peer voice 20 voip
preference 1 (this says to use this dial peer first and the other one
second, put your Pub first and the Sub second)
destination-pattern [1-8]... (You could change this to dail preference for
your shop)
progress_ind setup enable 3
voice-class codec 1
voice-class h323 1
session target ipv4:10.2.0.20 (Your CallManager)
dtmf-relay cisco-rtp h245-signal h245-alphanumeric
no vad
dial-peer voice 21 voip
preference 2
destination-pattern [1-8]... (You could change this to dail preference for
your shop)
progress_ind setup enable 3
voice-class codec 1
voice-class h323 1
session target ipv4:10.2.0.21 (Your CallManager)
dtmf-relay cisco-rtp h245-signal h245-alphanumeric
no vad
Does this help?
_____
From: James Grace [mailto:jgrace at digitelusa.net]
Sent: Tuesday, March 28, 2006 2:27 PM
To: Leetun, Rob
Subject: RE: [cisco-voip] h323 gw config
Im a little confuse on the voip dial peer
My callmanager is 10.2.0.20 and 21. can you send me a example of a good
voip dial peer .
_____
From: Leetun, Rob [mailto:rleetun at co.boulder.co.us]
Sent: Tuesday, March 28, 2006 3:41 PM
To: James Grace
Subject: RE: [cisco-voip] h323 gw config
Hi James,
Here is the config off one of our gateways. Good Luck
Rob
voice service voip
modem passthrough nse codec g711ulaw
!
!
voice class codec 1
codec preference 1 g711ulaw
codec preference 2 g729r8
!
!
!
voice class h323 1
h225 timeout tcp establish 3
!
voice-port 1/0:23
input gain 6
output attenuation 3
no vad
bearer-cap Speech
!
voice-port 1/1:23
input gain 6
output attenuation 3
no vad
bearer-cap Speech
!
!
no mgcp package-capability res-package
mgcp package-capability sst-package
no mgcp timer receive-rtcp
mgcp sdp simple
mgcp fax t38 inhibit
mgcp rtp payload-type g726r16 static
!
!
dial-peer cor custom
!
!
!
dial-peer voice 1 pots
incoming called-number ....
direct-inward-dial
!
dial-peer voice 10 voip
preference 1
destination-pattern [1-8]...
progress_ind setup enable 3
voice-class codec 1
voice-class h323 1
session target ipv4:192.168.20.2
dtmf-relay cisco-rtp h245-signal h245-alphanumeric
no vad
!
dial-peer voice 11 voip
preference 3
destination-pattern [1-8]...
progress_ind setup enable 3
voice-class codec 1
voice-class h323 1
session target ipv4:192.168.20.3
dtmf-relay cisco-rtp h245-signal h245-alphanumeric
no vad
!
dial-peer voice 2 pots
destination-pattern 9..........
port 1/0:23
!
dial-peer voice 3 pots
destination-pattern 9...........
port 1/0:23
!
dial-peer voice 911 pots
destination-pattern 911
port 1/0:23
prefix 911
!
dial-peer voice 9911 pots
destination-pattern 9911
port 1/0:23
prefix 911
!
dial-peer voice 12 voip
preference 2
destination-pattern [1-8]...
progress_ind setup enable 3
voice-class codec 1
voice-class h323 1
session target ipv4:192.168.248.22
dtmf-relay cisco-rtp h245-signal h245-alphanumeric
no vad
_____
From: cisco-voip-bounces at puck.nether.net
[mailto:cisco-voip-bounces at puck.nether.net] On Behalf Of James Grace
Sent: Tuesday, March 28, 2006 1:15 PM
To: cisco-voip at puck.nether.net
Cc: Scott.Voll at wesd.org
Subject: [cisco-voip] h323 gw config
Trying to config a h323 gw for the first time.
!
voice call send-alert
voice rtp send-recv
!
controller T1 0/0/1
framing esf
linecode b8zs
ds0-group 0 timeslots 9-24 type fxo-ground-start
!
!
interface GigabitEthernet0/0
description uplink to Core SW
ip address 10.2.0.5 255.255.255.0
duplex full
speed 100
h323-gateway voip bind srcaddr 10.2.0.5
!
ip route 0.0.0.0 0.0.0.0 10.2.0.254
!
voice-port 0/0/1:0
output attenuation 0
!
mgcp bind control source-interface GigabitEthernet0/0
mgcp bind media source-interface GigabitEthernet0/0
!
mgcp profile default
!
dial-peer voice 1 pots
description "outbound LD calls"
destination-pattern 9T
incoming called-number .
direct-inward-dial
port 0/0/1:0
so do we need a voip dial peer aswell. And on our CM we are using the 9.@
with discard predot will this work with the below dial peer. Also we have
a T1 with groudstart from the carrier, how do my controller look
James D. Grace
CCNP CCNA MCSE MCDBA
Sr. System Engineer / Professional Svc.
Digitel Corporation
-------------- next part --------------
An HTML attachment was scrubbed...
URL: https://puck.nether.net/pipermail/cisco-voip/attachments/20060328/abecbf5c/attachment-0001.html
More information about the cisco-voip
mailing list