[cisco-voip] Alerting Name being passed to PBX

[Tim Smith]

So thats a call from CCM to NEC...
Doesnt look like you are sending any Calling name information at all.
So I'd start looking at CCM until you can get a debug ISDN q931 which shows
you are sending the name..
Then you can look into the NEC.

Where do you have the calling names filled in on the phone config?
Do you have both Display and Alerting name set on the line? (normal and
ASCII?)

Calling party settings on the gateway itself?
Route patterns to the NEC set to offnet or on net?

You dont have any route patterns / translation patterns in there doing any
restriction on the calling name?

GW is definitely MGCP and set to Q.SIG?

Cheers,

Tim


On 8/6/08, William Roy <William.Roy at l7.com.au> wrote:
>
>  No we do not get connected name once the call is connected only calling
> number. This is a debug from an IP phone to a NEC phone
>
>
> ho-vgate-1#
> ho-vgate-1#
> *Aug  6 08:21:39.106: ISDN Se0/0/0:15 Q931: TX -> SETUP pd = 8  callref =
> 0x001E
>         Sending Complete
>         Bearer Capability i = 0x8090A3
>                 Standard = CCITT
>                 Transfer Capability = Speech
>                 Transfer Mode = Circuit
>                 Transfer Rate = 64 kbit/s
>         Channel ID i = 0xA9839F
>                 Exclusive, Channel 31
>         Calling Party Number i = 0x0081, '6005'
>                 Plan:Unknown, Type:Unknown
>         Called Party Number i = 0x80, '4723'
>                 Plan:Unknown, Type:Unknown
> *Aug  6 08:21:39.166: ISDN Se0/0/0:15 Q931: RX <- CALL_PROC pd = 8  callref
> = 0x801E
>         Channel ID i = 0xA9839F
>                 Exclusive, Channel 31
> *Aug  6 08:21:39.170: ISDN Se0/0/0:15 Q931: RX <- ALERTING pd = 8  callref
> = 0x801E
> *Aug  6 08:21:43.158: ISDN Se0/0/0:15 Q931: RX <- CONNECT pd = 8  callref =
> 0x801E
>         Progress Ind i = 0x8082 - Destination address is non-ISDN
>         Connected Number i = 0x0081, '4723'
> *Aug  6 08:21:43.162: ISDN Se0/0/0:15 Q931: TX -> CONNECT_ACK pd = 8
> callref = 0x001E
>
>  ------------------------------
> *From:* smithsonianwa at gmail.com [smithsonianwa at gmail.com] On Behalf Of Tim
> Smith [thsglobal at gmail.com]
> *Sent:* Wednesday, 6 August 2008 3:54 PM
> *To:* William Roy
> *Cc:* cisco-voip at puck.nether.net
> *Subject:* Re: [cisco-voip] Alerting Name being passed to PBX
>
>
>   Hi Wil,
>
> What do you see with a debug isdn q931?
>
> Do you get connected name once the call is established?
>
> Cheers,
>
> Tim.
>
>
>
>
>
> On 8/6/08, William Roy <William.Roy at l7.com.au> wrote:
>>
>>  I have NEC IPX2400 PBX connected to a ISR2851 via an QSIG E1 link. The
>> ISR is setup as an MGCP gateway with a CUCM 6.1 cluster. I am not seeing
>> Calling name being passed either from an NEC phone to a Cisco IP phone or
>> visa versa. Is there any debug I can run on the ISR to see if the cisco ip
>> phone is sending Calling name?
>>
>> regards
>> Wil
>>
>> _______________________________________________
>> cisco-voip mailing list
>> cisco-voip at puck.nether.net
>> https://puck.nether.net/mailman/listinfo/cisco-voip
>>
>>
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://puck.nether.net/pipermail/cisco-voip/attachments/20080806/0865e598/attachment.html>