Using no password?
DS
On Thu, 12 Apr 2001, Nathan Casassa wrote:
> I am living on the edge:
>
> LAB-2900-2> (enable) enable engineer
> Enter password:
> LAB-2900-2> (debug-eng)
>
> > -----Original Message-----
> > From: Shankar Vemulapalli [mailto:svemulap@cisco.com]
> > Sent: Wednesday, April 11, 2001 10:02 PM
> > To: Casassa, Nathan
> > Cc: 'Danny Sutantyo'; 'cisco-nsp@puck.nether.net'
> > Subject: RE: [nsp] Catalyst command
> >
> >
> > This is not officially supported by Cisco.
> > Btw - it is advised not use this mode as it is used only by the
> > engineering
> > and whoever
> > uses this does it at their own risk !
> >
> > /Shankar
> >
> > At 06:26 PM 4/11/2001, Casassa, Nathan wrote:
> > >I had this saved:
> > >
> > >Here's the trick to enter the secret engineer-mode in a catalyst 5K :
> > >
> > >With Supervisor-Engine I:
> > >
> > >Enter enable mode
> > >Do a SH VERSION (so that you get Hardware-,Firmware- and
> > Software-Versions)
> > >Type ENABLE ENGINEER
> > >You will be prompted for a password. Now this is very complex. You must
> > >enter the password in
> > >the following format:
> > >VTY VTY HW FW SW
> > >
> > >That is, the VTY-password followed by the VTY-password again, followed by
> > >the Hardware-Version,
> > >
> > >followed by the Software-version(no spaces, do not type the dots in the
> > >versions)
> > >
> > >Let's say (an assumption):
> > >
> > >the VTY-password is c
> > >
> > >the Hardware-version is 2.2
> > >
> > >the formware-version is 2.3
> > >
> > >then you would enter as the engineer-password:
> > >
> > >cc2223
> > >
> > >With Supervisor-Engine II:
> > >Enter enable mode
> > >Do a SH VERSION (so that you get Hardware-,Firmware- and
> > Software-Versions)
> > >Type ENABLE ENGINEER
> > >You will be prompted for a password. Now this is very complex. You must
> > >enter the password in
> > >the following format:
> > >VTY HW FW SW VTY
> > >
> > >That is, the VTY-password followed by the VTY-password again, followed by
> > >the Hardware-Version,
> > >
> > >followed by the Software-version (no spaces, do not type the dots in the
> > >versions).
> > >
> > >Let's say (an assumption):
> > >
> > >the VTY-password is c
> > >
> > >the Hardware-version is 2.2
> > >
> > >the formware-version is 2.3
> > >
> > >then you would enter as the engineer-password: c2223c
> > >
> > >
> > >You see, the difference between Supervisor I and II is just the position
> > >where the second VTY-password
> > >is placed.
> > >
> > >After you are in engineer-mode, you can display the available
> > functions by
> > >SH ?
> > >There will be a lot new (besides the know ones) functions available !!
> > >
> > >Great isn't it ?
> > >
> > >OK, here's a demonstration:
> > >
> > >sun>134.3.0.134
> > >
> > >' telnet to the catalyst
> > >
> > >Trying 134.3.0.134 ... Open
> > >
> > >
> > >
> > >Cisco Systems Console
> > >
> > >
> > >
> > >Enter password:
> > >
> > >' I entered "c"
> > >
> > >Console> enable
> > >
> > >Enter password:
> > >
> > >' I entered "c"
> > >
> > >Console> (enable) sh version
> > >
> > >WS-C5000 Software, Version McpSW: 4.4(1) NmpSW: 4.4(1)
> > >
> > >Copyright (c) 1995-1999 by Cisco Systems
> > >
> > >NMP S/W compiled on Jan 6 1999, 18:05:22
> > >
> > >MCP S/W compiled on Jan 06 1999, 17:50:33
> > >
> > >System Bootstrap Version: 2.2(2)
> > >
> > >Hardware Version: 2.3 Model: WS-C5000 Serial #: 006342981
> > >
> > >Mod Port Model Serial # Versions
> > >
> > >--- ---- ---------- --------- ----------------------------------------
> > >
> > >1 2 WS-X5009 006342981 Hw : 2.3
> > >
> > >Fw : 2.2(2)
> > >
> > >Fw1: 2.2(1)
> > >
> > >Sw : 4.4(1)
> > >
> > >2 24 WS-X5225R 015573453 Hw : 3.3
> > >
> > >Fw : 4.3(1)
> > >
> > >Sw : 4.4(1)
> > >
> > >3 24 WS-X5225R 013496932 Hw : 3.3
> > >
> > >Fw : 4.3(1)
> > >
> > >Sw : 4.4(1)
> > >
> > >4 2 WS-X5158 004446685 Hw : 1.2
> > >
> > >Fw : 1.3
> > >
> > >Fw1: 1.3
> > >
> > >Sw : 3.2(4)
> > >
> > >DRAM FLASH NVRAM
> > >
> > >Module Total Used Free Total Used Free Total Used Free
> > >
> > >------ ------- ------- ------- ------- ------- ------- ----- ----- -----
> > >
> > >1 20480K 10473K 10007K 4096K 3584K 512K 256K 130K 126K
> > >
> > >Uptime is 0 day, 5 hours, 8 minutes
> > >
> > >
> > >
> > >Console> (enable) enable engineer
> > >
> > >Enter password:
> > >
> > >' I entered a wrong password so that you see the reaction
> > >
> > >Sorry
> > >
> > >Console> (enable) enable engineer
> > >
> > >Enter password:
> > >
> > >' this time I entered "c232244c" because it is a Supervisor II engine
> > >
> > >' the result is the engineer-prompt "debug-eng"
> > >
> > >Console> (debug-eng) ?
> > >
> > >
> > >
> > >Commands:
> > >
> > >----------------------------------------------------------------------
> > >
> > >bootp Start a bootp download
> > >
> > >broadcast Broadcast a message
> > >
> > >call Call specified C function
> > >
> > >cam EARL utilities
> > >
> > >cdpd Start the CDP daemon
> > >
> > >clear Clear, use 'clear help' for more info
> > >
> > >configure Configure system from network
> > >
> > >connect Connect to FDDI ring
> > >
> > >copy Copy code between TFTP server and module
> > >
> > >ding Send index directed packet to port
> > >
> > >disable Disable privileged mode
> > >
> > >disconnect Disconnect from FDDI ring or disconnect user session
> > >
> > >download Download code to a processor
> > >
> > >enable Enable privileged mode
> > >
> > >erase Erase, use 'erase help' for more info
> > >
> > >failed_next Set Failed Next
> > >
> > >help Show this message
> > >
> > >history Show contents of history substitution buffer
> > >
> > >kill Send a signal to a process
> > >
> > >lcp Send console commands to an LCP
> > >
> > >packnvram pack NVRAM
> > >
> > >ping Send echo packets to hosts
> > >
> > >ps List current state of processes on the system
> > >
> > >quit Exit from the Admin session
> > >
> > >reconfirm Reconfirm VMPS
> > >
> > >reload Force software reload to linecard
> > >
> > >reset Reset system or module
> > >
> > >ibping Send Ibipc v2 pings
> > >
> > >scp SCP utilities
> > >
> > >scpmsg Send SCP message
> > >
> > >scpper Start SP performance test
> > >
> > >slpper Start SLP performance test
> > >
> > >sltask Start Salem task for slp link
> > >
> > >session Tunnel to ATM or Router module
> > >
> > >set Set, use 'set help' for more info
> > >
> > >show Show, use 'show help' for more info
> > >
> > >slip Attach/detach Serial Line IP interface
> > >
> > >snmpd Start the snmp daemon
> > >
> > >start_op_console Start Standby Supervisor Console
> > >
> > >switch Switch to standby <clock|supervisor>
> > >
> > >tcpactive Start TCP active download test
> > >
> > >tcpstandby Start TCP standby download test
> > >
> > >tcptest Start TCP download test
> > >
> > >tcpactnvram Start TCP active NVRAM test
> > >
> > >tcpsbynvram Start TCP standby NVRAM test
> > >
> > >telnet Telnet to a remote host
> > >
> > >telnetd Start the telnet daemon
> > >
> > >test Test, use 'test help' for more info
> > >
> > >traceroute Trace the route to a host
> > >
> > >upload Upload code from a processor
> > >
> > >wait Wait for x seconds
> > >
> > >whichbus Which bus mod/port is on
> > >
> > >whoisdnld Who is downloading
> > >
> > >whoisnvram Who is holding nvram
> > >
> > >write Write system configuration to terminal/network
> > >
> > >start_cl_console Start Clear Lake (NAM) Console
> > >
> > >Console> (debug-eng) show ?
> > >
> > >Show commands:
> > >
> > >-----------------------------------------------------------------
> > ---------
> > >
> > >show agc Show Actual Group Capability
> > >
> > >show agport Show Agport Information
> > >
> > >show alias Show aliases for commands
> > >
> > >show alloc Show mbuf and malloc allocation
> > >
> > >show arbiter Show Samba arbiter status
> > >
> > >show arp Show ARP table
> > >
> > >show asic Show asic information from the extended card feature table
> > >
> > >show asicreg Show ASIC registers
> > >
> > >show authentication Show authentication information
> > >
> > >show authentable Show nvram authentication table
> > >
> > >show avltree Show EARL AVL tree information
> > >
> > >show biga Show BIGA and Driver stats
> > >
> > >show bridge Show bridge information
> > >
> > >show bridgefddi Show bridge info on individual FDDI modules
> > >
> > >show blackcombreg Show Blackcmb Register
> > >
> > >show bcreg Show Blackcomb Register[range]
> > >
> > >show bcstatistics Show Blackcomb Statistics
> > >
> > >show bcsearch Show Blackcomb Search data
> > >
> > >show searchforever Show Blackcomb Search Forever
> > >
> > >show earlintrreg Show Earl Intr Register
> > >
> > >show lookupram Show Blackcomb Lookup Ram
> > >
> > >show looktable Show Blackcomb Lookup Table
> > >
> > >show indexram Show Blackcomb Index Ram
> > >
> > >show mappingram Show Blackcomb Mapping Ram
> > >
> > >show fidram Show Blackcomb Fid Ram
> > >
> > >show controlram Show Blackcomb Control Ram
> > >
> > >show fiforam Show Blackcomb Notify Fifo Ram
> > >
> > >show tbm Show Tremblant Register
> > >
> > >show tbmind Show Tremblant Indir Register
> > >
> > >show tbmstatus Show Tremblant Status
> > >
> > >show banfflog Show Banff log information
> > >
> > >show banffreg Show Banff Register
> > >
> > >show banffmet Show Banff MET
> > >
> > >show banffpb Show Banff Packet Buffer
> > >
> > >show banff-reset Show Banff reset counts
> > >
> > >show banff-list Show Banff free list
> > >
> > >show busnmi Show Switching Bus NMI setting
> > >
> > >show cam Show CAM table
> > >
> > >show cbl Show 8051 color blocking logic contents
> > >
> > >show cbpointer Show Config Block Pointers
> > >
> > >show cdp Show Cisco Discovery Protocol Information
> > >
> > >show cdpstat Show CDP statistics
> > >
> > >show cdptable Show CDP Cache Table Entries
> > >
> > >show cgmp Show CGMP info
> > >
> > >show checkinterval Show nvram check interval
> > >
> > >show code Show assembly code
> > >
> > >show config Show system configuration
> > >
> > >show counters Show port counters
> > >
> > >show cpumon Show CPUMON Settings
> > >
> > >show drip Show DRiP Information
> > >
> > >show dvlan Show dynamic vlan statistics
> > >
> > >show dvlan Show dynamic vlan statistics
> > >
> > >show ebcmodes Show EBC HW modes
> > >
> > >show fddi Show FDDI module entries
> > >
> > >show fddicam Show FDDI module CAM table
> > >
> > >show feature Show feature
> > >
> > >show flash Show system flash information
> > >
> > >show generic_counters Show generic counters
> > >
> > >show help Show this message
> > >
> > >show ibipc Show ibipc statistics
> > >
> > >show igmp Show IGMP information
> > >
> > >show imagemib Show image mib information
> > >
> > >show interface Show network interfaces
> > >
> > >show ip Show IP Information
> > >
> > >show log Show log information
> > >
> > >show logging Show system logging information
> > >
> > >show ltl Show 8051 local target logic contents
> > >
> > >show mac Show MAC information
> > >
> > >show macdbg Show MAC debug information
> > >
> > >show malloc Show malloc stats
> > >
> > >show mbuf Show mbuf and cluster statistics
> > >
> > >show mdg Show Multiple Default Gateway Debug Info
> > >
> > >show memuse Show memory usage by pid
> > >
> > >show mem Show memory contents
> > >
> > >show microcode Show microcode versions
> > >
> > >show module Show module information
> > >
> > >show multicast Show multicast information
> > >
> > >show mls Show multilayer switching information
> > >
> > >show netstat Show network statistics
> > >
> > >show ntp Show ntp statistics
> > >
> > >show nvramversion Show nvram version
> > >
> > >show nvstat Show Active Nvram Tasks Stats
> > >
> > >show option Show option
> > >
> > >show port Show port information
> > >
> > >show portdbg Show port debug information
> > >
> > >show portinfo Show portinfo structure
> > >
> > >show portreg Show port registers
> > >
> > >show protocolfilter Show protocolfilter information
> > >
> > >show pruning Show VTP pruning information
> > >
> > >show redunda_state Show redundancy state info
> > >
> > >show rif Show Routing Information Field (RIF) Table
> > >
> > >show rsmautostate Show RSM derived interface state enabled/disabled
> > >
> > >show saint Show saint registers
> > >
> > >show sbnvstat Show Standby Nvram Tasks Stats
> > >
> > >show sbyports Show Standby Ports usage status
> > >
> > >show sccstat Show SCC status
> > >
> > >show scpmem Show 8051 memory contents
> > >
> > >show scpmodstat Show SCP-Module Stats.
> > >
> > >show scpreg Show SCP registration table
> > >
> > >show scpstat Show SCP statistics
> > >
> > >show scptrace Show trace levels
> > >
> > >show semaphore Show semaphore information
> > >
> > >show slpreg Show SLP registration table
> > >
> > >show slpstat Show SLP statistics
> > >
> > >show snmp Show SNMP information
> > >
> > >show snmpd Show snmpd state information
> > >
> > >show softflag Show all softflags
> > >
> > >show span Show switch port analyzer information
> > >
> > >show spanningtree Show spantree port information
> > >
> > >show spantree Show spantree information
> > >
> > >show spoofing Show spoofing state
> > >
> > >show sprom Show Serial EEPROM
> > >
> > >show standbyports Show state of standby ports feature.
> > >
> > >show station Show Tokenring Station info
> > >
> > >show summertime Show state of summertime information
> > >
> > >show syndiag Show syndiags status
> > >
> > >show timer Show timer information
> > >
> > >show trport Show port status info for Token Ring port
> > >
> > >show trmod Show module details for Token Ring module
> > >
> > >show system Show system information
> > >
> > >show tacacs Show TACACS information
> > >
> > >show test Show results of diagnostic tests
> > >
> > >show time Show time of day
> > >
> > >show timezone Show the current timezone offset
> > >
> > >show tokenring Show tokenring information
> > >
> > >show top Show TopN report
> > >
> > >show tpoint Show trace points
> > >
> > >show trace Show trace settings
> > >
> > >show trunk Show trunk ports
> > >
> > >show users Show active Admin sessions
> > >
> > >show version Show version information
> > >
> > >show vlan Show Virtual LAN information
> > >
> > >show vlantbladr Show Vlan Port Table Address
> > >
> > >show vmps Show VMPS information
> > >
> > >show vtp Show VTP Information
> > >
> > >show whistler Show Whistler information
> > >
> > >
> > >
> > >
> > >
> > >Console> (debug-eng) exit
> > >
> > >' with "exit" I ended my telnet-session
> > >
> > >[Connection to 134.3.0.134 closed .....
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >show counters <mod/port> shows you SNMP and RMON counters.
> > >
> > >-----Original Message-----
> > >From: Danny Sutantyo [mailto:dsutanty@dsutanty-wkst.sc.intel.com]
> > >Sent: Wednesday, April 11, 2001 8:17 PM
> > >To: cisco-nsp@puck.nether.net
> > >Subject: [nsp] Catalyst command
> > >
> > >
> > >Does any body know about "enable engineer" (not regular "enable") command
> > >in Catalyst? I heard
> > >it's undocumented, and do you know what it does?
> > >
> > >DS
> >
>
This archive was generated by hypermail 2b29 : Sun Aug 04 2002 - 04:12:34 EDT