Not really. Based on a private conversation follow-up, I received
confirmation that changing the vlan membership fixed the issue. I
believe the native vlan the trunk ports belonged to did not actually
exist and may have been removed at some point. The error message is a
bit misleading.
-- steve
--- Jeremie Meyer <jmeyer@easynet.fr> wrote:
> Steve : do you mean that when you reset a card, before reading the
> configuration file, the switch puts every ports into the vlan 1 ?
>
> Jeremie
> ----- Original Message -----
> From: "Stephen Gill" <gillsr@yahoo.com>
> To: "Jeremie Meyer" <jmeyer@easynet.fr>; <cisco-nsp@puck.nether.net>
> Sent: Tuesday, June 05, 2001 5:22 PM
> Subject: Re: [nsp] "inactive" ports? (WS6k, SUP1AE+MSFC/2xGBIC)
>
>
> > I believe setting the trunk ports back to vlan 1 solved the
> problem.
> >
> > -- steve
> >
> > --- Jeremie Meyer <jmeyer@easynet.fr> wrote:
> > > I had this problem once, but it was'nt on an MSFC card. A reset
> of
> > > the card solved the problem
> > >
> > > Jeremie
> > >
> > > ----- Original Message -----
> > > From: "Stephen Gill" <gillsr@yahoo.com>
> > > To: "'Christopher Neill'" <noise@cow.org>;
> > > <cisco-nsp@puck.nether.net>
> > > Sent: Tuesday, June 05, 2001 2:59 AM
> > > Subject: RE: [nsp] "inactive" ports? (WS6k, SUP1AE+MSFC/2xGBIC)
> > >
> > >
> > > > Have you checked to make sure vlan 60 still exists?
> > > >
> > > > -- steve
> > > >
> > > > -----Original Message-----
> > > > From: Christopher Neill [mailto:noise@cow.org]
> > > > Sent: Monday, June 04, 2001 7:37 PM
> > > > To: cisco-nsp@puck.nether.net
> > > > Subject: [nsp] "inactive" ports? (WS6k, SUP1AE+MSFC/2xGBIC)
> > > >
> > > >
> > > > anyone ever get this jazz?
> > > >
> > > > switch02.sjc (enable) sh port stat 1
> > > > Port Name Status Vlan Duplex Speed
> Type
> > > > ----- ------------------ ---------- ---------- ------ -----
> > > ------------
> > > > 1/1 inactive 60 full 1000
> > > 1000BaseSX
> > > > 1/2 inactive 60 full 1000
> > > 1000BaseSX
> > > > switch02.sjc (enable) set port dis 1/1-2
> > > > This command may disconnect your telnet session.
> > > > Do you want to continue (y/n) [n]?y
> > > > Ports 1/1-2 disabled.
> > > > switch02.sjc (enable) set port en 1/1
> > > > Failed to enable port 1/1.
> > > > Port may be faulty.
> > > > switch02.sjc (enable) set port en 1/2
> > > > Failed to enable port 1/2.
> > > > Port may be faulty.
> > > >
> > > > --
> > > > $Id: .sig,v 1.43 2001/04/07 18:00:44 noise Exp $
> > > > "It's a kind of love affair. If you spend half an hour making
> > > scrambled eggs
> > > > in the morning for someone, then you really love them." -Chef
> > > Boulud
> > > >
> > > >
> > > > _________________________________________________________
> > > > Do You Yahoo!?
> > > > Get your free @yahoo.com address at http://mail.yahoo.com
> > > >
> > > >
> > >
> >
> >
> > __________________________________________________
> > Do You Yahoo!?
> > Get personalized email addresses from Yahoo! Mail - only $35
> > a year! http://personal.mail.yahoo.com/
> >
>
__________________________________________________
Do You Yahoo!?
Get personalized email addresses from Yahoo! Mail - only $35
a year! http://personal.mail.yahoo.com/
This archive was generated by hypermail 2b29 : Sun Aug 04 2002 - 04:12:40 EDT