[alcatel-nsp] Alcatel-Juniper 10G Interop
Ryan Landry
Ryan.Landry at TELUS.COM
Mon Feb 7 12:12:59 EST 2011
there's really not much to it. keep in mind our boxes are IOM3-XP. i'm
also assuming you are using lan-phy for b2b 10GE.
<snip> show version
Hostname: <snip>
Model: srx5800
JUNOS Software Release [10.0S11.3]
<snip># show interfaces xe-10/1/0
description "<snip> 1/1/2";
mtu 9192;
unit 0 {
family inet {
address <snip>/31;
}
family iso;
}
[edit]
<snip> show interfaces xe-10/1/0
Physical interface: xe-10/1/0, Enabled, Physical link is Up
Interface index: 143, SNMP ifIndex: 129
Description: <snip> 1/1/2
Link-level type: Ethernet, MTU: 9192, LAN-PHY mode, Speed: 10Gbps,
Loopback: None,
Source filtering: Disabled, Flow control: Enabled
Device flags : Present Running
Interface flags: SNMP-Traps Internal: 0x4000
Link flags : None
CoS queues : 8 supported, 4 maximum usable queues
Schedulers : 0
Current address: 00:24:dc:25:46:9b, Hardware address: 00:24:dc:25:46:9b
Last flapped : 2011-01-14 11:52:08 MST (3w2d 22:10 ago)
Input rate : 97616 bps (30 pps)
Output rate : 156984 bps (37 pps)
Active alarms : None
Active defects : None
PCS statistics Seconds
Bit errors 1
Errored blocks 1
Logical interface xe-10/1/0.0 (Index 70) (SNMP ifIndex 167)
Flags: SNMP-Traps 0x4000000 Encapsulation: ENET2
Input packets : 26044773541
Output packets: 43143859112
Security: Zone: <snip>
Allowed host-inbound traffic : <snip>
Protocol inet, MTU: 9178
Addresses, Flags: Is-Preferred Is-Primary
Destination: <snip>/31, Local: <snip>
Protocol iso, MTU: 9175
Protocol multiservice, MTU: Unlimited
A:<snip>>config>port# show version
TiMOS-C-6.1.R19 cpm/hops ALCATEL SR 7750 Copyright (c) 2000-2010
Alcatel-Lucent.
All rights reserved. All use subject to applicable license agreements.
Built on Tue Dec 7 13:21:51 PST 2010 by builder in
/rel6.1/b1/R19/panos/main
A:<snip>>config>port# info
----------------------------------------------
description "<snip> 10/1/0"
ethernet
network
queue-policy "<snip>"
exit
exit
no shutdown
----------------------------------------------
A:<snip>config>port# show port 1/1/2
===========================================================================
====
Ethernet Interface
===========================================================================
====
Description : <snip> 10/1/0
Interface : 1/1/2 Oper Speed : 10 Gbps
Link-level : Ethernet Config Speed : N/A
Admin State : up Oper Duplex : full
Oper State : up Config Duplex : N/A
Physical Link : Yes MTU : 9212
Single Fiber Mode : No
IfIndex : 35717120 Hold time up : 0
seconds
Last State Change : 01/14/2011 18:52:39 Hold time down : 0
seconds
Last Cleared Time : N/A DDM Events : Enabled
Configured Mode : network Encap Type : null
Dot1Q Ethertype : 0x8100 QinQ Ethertype : 0x8100
PBB Ethertype : 0x88e7
Ing. Pool % Rate : 100 Egr. Pool % Rate : 100
Ing. Pool Policy : n/a
Egr. Pool Policy : n/a
Net. Egr. Queue Pol: <snip>
Egr. Sched. Pol : n/a
Auto-negotiate : N/A MDI/MDX : N/A
Accounting Policy : None Collect-stats :
Disabled
Egress Rate : Default Ingress Rate : Default
Load-balance-algo : default LACP Tunnel :
Disabled
Down-when-looped : Disabled Keep-alive : 10
Loop Detected : False Retry : 120
Configured Address : 00:1a:f0:bd:88:60
Hardware Address : 00:1a:f0:bd:88:60
Cfg Alarm : remote local
Alarm Status :
Transceiver Data
Transceiver Type : XFP
Model Number : 3HE00566AAAA01 ALA IPUIARSDAA
TX Laser Wavelength: 850 nm Diag Capable : yes
Connector Code : LC Vendor OUI :
00:01:9c
Manufacture date : 2008/10/16 Media :
Ethernet
Serial Number : <snip>
Part Number : <snip>
Optical Compliance : 10GBASE-SR 10GBASE-SW
Link Length support: 300m for 50u EBW; 100m for 50u MMF; 33m for 62.5u MMF
===========================================================================
====
Transceiver Digital Diagnostic Monitoring (DDM)
===========================================================================
====
Value High Alarm High Warn Low Warn Low
Alarm
---------------------------------------------------------------------------
----
Temperature (C) +37.8 +75.0 +70.0 -15.0
-20.0
Tx Bias Current (mA) 6.8 10.0 9.0 2.5
2.0
Tx Output Power (dBm) -2.75 1.00 0.00 -4.50
-6.00
Rx Optical Power (avg dBm) -2.89 0.00 -0.70 -10.00
-11.00
Aux1: 5.0 Voltage (V) 4.99 6.55 6.55 0.00
0.00
Aux2: 3.3 Voltage (V) 3.26 6.55 6.55 0.00
0.00
===========================================================================
====
===========================================================================
====
Traffic Statistics
===========================================================================
====
Input
Output
---------------------------------------------------------------------------
----
Octets 200501858087
691471368189
Packets 500226766
726140079
Errors 0
0
===========================================================================
====
A:<snip>>config>router>if# info
----------------------------------------------
address <snip>/31
port 1/1/2
exit
qos <snip>
----------------------------------------------
From: Kevin Billings <kevin.billings at spirittelecom.com>
Date: Mon, 7 Feb 2011 09:56:07 -0700
To: Ryan Landry <Ryan.Landry at TELUS.COM>, "alcatel-nsp at puck.nether.net"
<alcatel-nsp at puck.nether.net>
Subject: RE: [alcatel-nsp] Alcatel-Juniper 10G Interop
This one got me. Can you share your port cfg?
From: Ryan Landry [mailto:Ryan.Landry at TELUS.COM]
Sent: Monday, February 07, 2011 11:50 AM
To: Kevin Billings; alcatel-nsp at puck.nether.net
Subject: Re: [alcatel-nsp] Alcatel-Juniper 10G Interop
we have 7750's connected to SRX5800's in our lab and production (similar
chassis and JunOS as MX) without any issues.
From: Kevin Billings <kevin.billings at spirittelecom.com>
Date: Mon, 7 Feb 2011 09:09:26 -0700
To: "alcatel-nsp at puck.nether.net" <alcatel-nsp at puck.nether.net>
Subject: [alcatel-nsp] Alcatel-Juniper 10G Interop
Hello All,
I am having trouble getting a MX960 10G port to connect to our 7750 SR12.
Both ports are up however we can¹t pass any traffic between us. I show
egress traffic, but no ingress and the MX960 sees the same. Has anyone
seen this on a mx960. I have tested the Alcatel port connected to the
MX960 to a Brocade MLXe-8 and everything works fine. I have connected the
MX960 to a MLXe and I see the same results so it looks like a MX issue.
Thanks
kevin
More information about the alcatel-nsp
mailing list