[alcatel-nsp] Alcatel-Juniper 10G Interop
Ryan Landry
Ryan.Landry at TELUS.COM
Mon Feb 7 12:29:21 EST 2011
sorry, forgot to include this which might help you in your troubleshooting
on the MX (ie: make sure you are actually sending/receiving light on both
ends at a good level). most newer xfp's support DOM/DDM stats like this. i
have already included the 7750 side previously.
<snip> show interfaces diagnostics optics xe-10/1/0
Physical interface: xe-10/1/0
Laser bias current : 7.538 mA
Laser output power : 0.5120 mW / -2.91 dBm
Module temperature : 33 degrees C / 92 degrees
F
Laser rx power : 0.4660 mW / -3.32 dBm
On 11-02-07 10:12 AM, "Ryan Landry" <Ryan.Landry at telus.com> wrote:
>there's really not much to it. keep in mind our boxes are IOM3-XP. i'm
>also assuming you are using lan-phy for b2b 10GE.
>
><snip> show version
>Hostname: <snip>
>Model: srx5800
>JUNOS Software Release [10.0S11.3]
>
>
><snip># show interfaces xe-10/1/0
>description "<snip> 1/1/2";
>mtu 9192;
>unit 0 {
> family inet {
> address <snip>/31;
> }
> family iso;
>}
>
>[edit]
>
>
><snip> show interfaces xe-10/1/0
>Physical interface: xe-10/1/0, Enabled, Physical link is Up
> Interface index: 143, SNMP ifIndex: 129
> Description: <snip> 1/1/2
> Link-level type: Ethernet, MTU: 9192, LAN-PHY mode, Speed: 10Gbps,
>Loopback: None,
> Source filtering: Disabled, Flow control: Enabled
> Device flags : Present Running
> Interface flags: SNMP-Traps Internal: 0x4000
> Link flags : None
> CoS queues : 8 supported, 4 maximum usable queues
> Schedulers : 0
> Current address: 00:24:dc:25:46:9b, Hardware address: 00:24:dc:25:46:9b
> Last flapped : 2011-01-14 11:52:08 MST (3w2d 22:10 ago)
> Input rate : 97616 bps (30 pps)
> Output rate : 156984 bps (37 pps)
> Active alarms : None
> Active defects : None
> PCS statistics Seconds
> Bit errors 1
> Errored blocks 1
>
> Logical interface xe-10/1/0.0 (Index 70) (SNMP ifIndex 167)
> Flags: SNMP-Traps 0x4000000 Encapsulation: ENET2
> Input packets : 26044773541
> Output packets: 43143859112
> Security: Zone: <snip>
> Allowed host-inbound traffic : <snip>
> Protocol inet, MTU: 9178
> Addresses, Flags: Is-Preferred Is-Primary
> Destination: <snip>/31, Local: <snip>
> Protocol iso, MTU: 9175
> Protocol multiservice, MTU: Unlimited
>
>
>
>A:<snip>>config>port# show version
>TiMOS-C-6.1.R19 cpm/hops ALCATEL SR 7750 Copyright (c) 2000-2010
>Alcatel-Lucent.
>All rights reserved. All use subject to applicable license agreements.
>Built on Tue Dec 7 13:21:51 PST 2010 by builder in
>/rel6.1/b1/R19/panos/main
>
>
>A:<snip>>config>port# info
>----------------------------------------------
> description "<snip> 10/1/0"
> ethernet
> network
> queue-policy "<snip>"
> exit
> exit
> no shutdown
>----------------------------------------------
>A:<snip>config>port# show port 1/1/2
>
>==========================================================================
>=
>====
>Ethernet Interface
>==========================================================================
>=
>====
>Description : <snip> 10/1/0
>Interface : 1/1/2 Oper Speed : 10 Gbps
>
>Link-level : Ethernet Config Speed : N/A
>
>Admin State : up Oper Duplex : full
>
>Oper State : up Config Duplex : N/A
>
>Physical Link : Yes MTU : 9212
>
>Single Fiber Mode : No
>
>IfIndex : 35717120 Hold time up : 0
>seconds
>Last State Change : 01/14/2011 18:52:39 Hold time down : 0
>seconds
>Last Cleared Time : N/A DDM Events : Enabled
>
>
>Configured Mode : network Encap Type : null
>
>Dot1Q Ethertype : 0x8100 QinQ Ethertype : 0x8100
>
>PBB Ethertype : 0x88e7
>
>Ing. Pool % Rate : 100 Egr. Pool % Rate : 100
>
>Ing. Pool Policy : n/a
>Egr. Pool Policy : n/a
>Net. Egr. Queue Pol: <snip>
>Egr. Sched. Pol : n/a
>Auto-negotiate : N/A MDI/MDX : N/A
>
>Accounting Policy : None Collect-stats :
>Disabled
>Egress Rate : Default Ingress Rate : Default
>
>Load-balance-algo : default LACP Tunnel :
>Disabled
>
>Down-when-looped : Disabled Keep-alive : 10
>
>Loop Detected : False Retry : 120
>
>
>Configured Address : 00:1a:f0:bd:88:60
>Hardware Address : 00:1a:f0:bd:88:60
>Cfg Alarm : remote local
>Alarm Status :
>
>Transceiver Data
>
>Transceiver Type : XFP
>
>Model Number : 3HE00566AAAA01 ALA IPUIARSDAA
>
>TX Laser Wavelength: 850 nm Diag Capable : yes
>
>Connector Code : LC Vendor OUI :
>00:01:9c
>Manufacture date : 2008/10/16 Media :
>Ethernet
>Serial Number : <snip>
>Part Number : <snip>
>Optical Compliance : 10GBASE-SR 10GBASE-SW
>
>Link Length support: 300m for 50u EBW; 100m for 50u MMF; 33m for 62.5u MMF
>
>
>==========================================================================
>=
>====
>Transceiver Digital Diagnostic Monitoring (DDM)
>==========================================================================
>=
>====
> Value High Alarm High Warn Low Warn Low
>Alarm
>--------------------------------------------------------------------------
>-
>----
>Temperature (C) +37.8 +75.0 +70.0 -15.0
>-20.0
>Tx Bias Current (mA) 6.8 10.0 9.0 2.5
>2.0
>Tx Output Power (dBm) -2.75 1.00 0.00 -4.50
>-6.00
>Rx Optical Power (avg dBm) -2.89 0.00 -0.70 -10.00
>-11.00
>Aux1: 5.0 Voltage (V) 4.99 6.55 6.55 0.00
>0.00
>Aux2: 3.3 Voltage (V) 3.26 6.55 6.55 0.00
>0.00
>==========================================================================
>=
>====
>
>==========================================================================
>=
>====
>Traffic Statistics
>==========================================================================
>=
>====
> Input
>Output
>--------------------------------------------------------------------------
>-
>----
>Octets 200501858087
>691471368189
>Packets 500226766
>726140079
>Errors 0
> 0
>==========================================================================
>=
>====
>
>A:<snip>>config>router>if# info
>----------------------------------------------
> address <snip>/31
> port 1/1/2
> exit
> qos <snip>
>----------------------------------------------
>
>
>
>
>From: Kevin Billings <kevin.billings at spirittelecom.com>
>Date: Mon, 7 Feb 2011 09:56:07 -0700
>To: Ryan Landry <Ryan.Landry at TELUS.COM>, "alcatel-nsp at puck.nether.net"
><alcatel-nsp at puck.nether.net>
>Subject: RE: [alcatel-nsp] Alcatel-Juniper 10G Interop
>
>
>This one got me. Can you share your port cfg?
>
>From: Ryan Landry [mailto:Ryan.Landry at TELUS.COM]
>Sent: Monday, February 07, 2011 11:50 AM
>To: Kevin Billings; alcatel-nsp at puck.nether.net
>Subject: Re: [alcatel-nsp] Alcatel-Juniper 10G Interop
>
>
>
>we have 7750's connected to SRX5800's in our lab and production (similar
>chassis and JunOS as MX) without any issues.
>
>
>
>From: Kevin Billings <kevin.billings at spirittelecom.com>
>Date: Mon, 7 Feb 2011 09:09:26 -0700
>To: "alcatel-nsp at puck.nether.net" <alcatel-nsp at puck.nether.net>
>Subject: [alcatel-nsp] Alcatel-Juniper 10G Interop
>
>
>
>Hello All,
>
>I am having trouble getting a MX960 10G port to connect to our 7750 SR12.
>Both ports are up however we can¹t pass any traffic between us. I show
>egress traffic, but no ingress and the MX960 sees the same. Has anyone
>seen this on a mx960. I have tested the Alcatel port connected to the
>MX960 to a Brocade MLXe-8 and everything works fine. I have connected the
>MX960 to a MLXe and I see the same results so it looks like a MX issue.
>
>Thanks
>
>kevin
>
>
>_______________________________________________
>alcatel-nsp mailing list
>alcatel-nsp at puck.nether.net
>https://puck.nether.net/mailman/listinfo/alcatel-nsp
More information about the alcatel-nsp
mailing list