[cisco-bba] PPPoE and many virtual-templates (per subif/vlan)

[Tassos Chatzithomaoglou]

Maybe i'm missing something here.

I tried all available commands under an ethernet subif, but i didn't find any option for enabling 
different pppoe config (vt) per subif.

Andy Schutz (aschutz) wrote on 8/3/2005 19:07:

> Yes, it should. 
> 
> 
>>-----Original Message-----
>>From: Tassos Chatzithomaoglou [mailto:achatz at forthnet.gr] 
>>Sent: Tuesday, March 08, 2005 10:57 AM
>>To: aschutz at cisco.com
>>Cc: 'cisco-bba'
>>Subject: Re: [cisco-bba] PPPoE and many virtual-templates 
>>(per subif/vlan)
>>
>>Thanks Andy ;-)
>>
>>This seems to be exactly what i was looking for.
>>
>>Do you know if this bba-group setup will work for ethernet 
>>subinterfaces too?
>>
>>Andy Schutz (aschutz) wrote on 8/3/2005 18:15:
>>
>>>Try using bba-groups:
>>>
>>
>>http://www.cisco.com/en/US/partner/products/hw/routers/ps133/p
>>roducts_config
>>
>>>uration_guide_chapter09186a0080175167.html#wp1050602
>>>
>>>Cheers,
>>>
>>>Andy 
>>>
>>>
>>>
>>>>-----Original Message-----
>>>>From: cisco-bba-bounces at puck.nether.net 
>>>>[mailto:cisco-bba-bounces at puck.nether.net] On Behalf Of 
>>>>Tassos Chatzithomaoglou
>>>>Sent: Tuesday, March 08, 2005 7:22 AM
>>>>To: cisco-bba
>>>>Subject: [cisco-bba] PPPoE and many virtual-templates (per 
>>
>>subif/vlan)
>>
>>>>I'm using the following config in order to accept and 
>>>>terminate PPPoE connections on a 7200 router.
>>>>The 7200 is connected through ATM/ima with a 6015 dslam.
>>>>
>>>>I'm trying to associate PPPoE users to different 
>>>>virtual-templates, based on the atm subif (or maybe 
>>>>vlan in the future) on which they are terminated.
>>>>
>>>>!--------------------------------------------------
>>>>vpdn-group PPPoE-USERS
>>>> accept-dialin
>>>>  protocol pppoe
>>>>  virtual-template 1
>>>>!
>>>>!
>>>>vc-class atm PPPoE-128
>>>>  protocol pppoe
>>>>  vbr-nrt 128 32
>>>>  encapsulation aal5snap
>>>>!
>>>>vc-class atm PPPoE-384
>>>>  protocol pppoe
>>>>  ubr 384
>>>>  encapsulation aal5snap
>>>>!
>>>>!
>>>>interface ATM2/ima1.1 multipoint
>>>> description ** subif 1**
>>>> range PPPoE-1 pvc 8/35 8/36
>>>>  class-range PPPoE-384
>>>> !
>>>>!
>>>>interface ATM2/ima1.2 multipoint
>>>> description ** subif 2**
>>>> range PPPoE-2 pvc 9/35 9/36
>>>>  class-range PPPoE-128
>>>>!--------------------------------------------------
>>>>
>>>>When using PPPoE, is there a way i can define another 
>>>>virtual-template to be used under the 2nd atm 
>>>>subif?
>>>>Maybe i have to change the encapsulation from aal5snap to 
>>>>something else, but then will it work with 
>>>>PPPoE?
>>>>
>>>>When using pppovlan (PPPoE over vlan) as encapsulation is 
>>>>there a way i can configure different vt 
>>>>per vlan?
>>>>
>>>>PS: If i use PPPoA (and aal5mux), i can configure one 
>>>>-different- vt under each vc-class, so this 
>>>>scenario is working fine.
>>>>
>>>>
>>>>_______________________________________________
>>>>cisco-bba mailing list
>>>>cisco-bba at puck.nether.net
>>>>https://puck.nether.net/mailman/listinfo/cisco-bba
>>>>
>>>
>>>
> 

-- 
***************************************
         Tassos Chatzithomaoglou
Network Design & Development Department
              FORTHnet S.A.
          <achatz at forthnet.gr>
***************************************