[cisco-bba] MTU challenges on Cisco 7206VXR

[Frank Bulk]

Let me expand the question:

What combination of:
	mtu xxxx
	ip tcp adjust-mss yyyy
	ppp mtu adaptive
should I be using on a Virtual Template?  I have none of them today, and
only with PPPoE do things break sometimes.

Frank

-----Original Message-----
From: cisco-bba-bounces at puck.nether.net
[mailto:cisco-bba-bounces at puck.nether.net] On Behalf Of Frank Bulk
Sent: Thursday, November 06, 2008 9:36 AM
To: rblayzor at inoc.net; cisco-bba at puck.nether.net
Subject: Re: [cisco-bba] MTU challenges on Cisco 7206VXR

Should I be applying
        ip tcp adjust-mss 1492
to the Virtual-Template, or
        mtu 1492

I have a potential maintenance window tonight and I would like to sneak this
in there.

Frank

-----Original Message-----
From: cisco-bba-bounces at puck.nether.net
[mailto:cisco-bba-bounces at puck.nether.net] On Behalf Of Frank Bulk
Sent: Thursday, March 13, 2008 2:02 PM
To: rblayzor at inoc.net
Cc: cisco-bba at puck.nether.net
Subject: Re: [cisco-bba] MTU challenges on Cisco 7206VXR

Thanks for the feedback.  So, do you think that 'mtu 1504' is a valid
configuration item and I should leave that alone?  I would prefer not to
drop 8 bytes from my PPPoA customers if removing the 'mtu 1504' entry would
solve the problem.

Frank

-----Original Message-----
From: Robert Blayzor [mailto:rblayzor.bulk at inoc.net]
Sent: Thursday, March 13, 2008 7:39 AM
To: frnkblk at iname.com
Cc: cisco-bba at puck.nether.net
Subject: Re: [cisco-bba] MTU challenges on Cisco 7206VXR

Frank Bulk - iNAME wrote:
> Ok, I agree.  So where are the problems coming from?
>
> I do see that on the "root" ATM interface I have the following entered:
>       interface ATM4/0
>        mtu 1504
>        no ip address
>        no atm ilmi-keepalive
>       !
> And the PVCs are defined under a sub-interface as follows:
>       interface ATM4/0.100 multipoint
>        pvc 0/261
>         encapsulation aal5mux ppp Virtual-Template1
>        !
>        pvc 0/262
>         encapsulation aal5snap
>         protocol pppoe
>        !
>        pvc 0/263
>         encapsulation aal5mux ppp Virtual-Template1
>        !
>
> Is it possible that the PVC connections are inheriting the 1504 for the
> ATM4/0 interface and that I should delete that line altogether?


I'd leave the MTU at default on the ATM interface and change the MTU on
your virtual-template to 1492.  We have tens of thousands of
DSL/Ethernet subs using PPPoE/oA with no MTU problems at all.  Usually
the device terminating the PPPoX is smart enough to know to adjust the
MTU... some not so much.

There are some devices in which you have to clamp the mss because the
client can't figure it out for some reason... however, that should be
few and far between.


--
Robert Blayzor
INOC
rblayzor at inoc.net
http://www.inoc.net/~rblayzor/

 > SELECT * FROM users WHERE clue > 0
0 rows returned

_______________________________________________
cisco-bba mailing list
cisco-bba at puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-bba

_______________________________________________
cisco-bba mailing list
cisco-bba at puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-bba