[cisco-nas] Re: [c-ubr] Missing Calling-Station-ID in Access-Request

Nilesh Naik qmailindia at yahoo.com
Fri May 2 10:19:36 EDT 2003


Hi 

   Thanx a lot , but unfortunately i tried that too
couple of times but that too didt worked , i do not
have the cco passwd so if you dont mind request you to
copy-paste that part from the web page ,

warm regards
Prashant
  
--- Adeel Ahmed <adeel_373 at yahoo.com> wrote:
> I think you will need to configure the following
> commands to get this working:
> 
> radius-server vsa send accounting                   
>  
> radius-server vsa send authentication
> 
> 
> Take a look at the following example for reference:
> 
>
http://www.cisco.com/en/US/partner/products/sw/iosswrel/ps1839/products_feature_guide_chapter09186a00800b5de5.html
> 
> Eventhough the example is not from a uBR7246 you can
> see the NAS(AS5300) sending radius attribute 31 to
> the
> radius-server.
> 
> Hope this helps !
> 
> Adeel.
> 
> --- Nilesh Naik <qmailindia at yahoo.com> wrote:
> > Hi all 
> > 
> >   we rae using cisco uBR 7246, as our PPPoE
> > concentrator and NAS , we are running IOS (tm)
> 7200
> > Software (UBR7200-IK8S-M), Version 12.2(11)BC3,
> > EARLY
> > DEPLOYMENT RELEASE SOFTWARE (fc2)  on this uBR , 
> > 
> >    we are presently using the Radius
> Authentication
> > for all the PPPoE dialin Users , but when i see in
> > the
> > debug mode by enabling "debug radius", debug aaa
> > authentication" & "debug aaa accounting" i cant
> see
> > cisco uBR sending "Calling-Station-Id" attribute
> to
> > the radius , which i think sould contain value of
> > the
> > customer's MAC Address if i am correct ?? pls
> > correct
> > me if i am wrong here ? 
> > 
> >    now i check out every option on the Ubr to
> enable
> > this i even tried these following commands 
> > 
> > aaa group server radius accountgroup
> >  server 20.17.92.2 auth-port 1645 acct-port 1646
> >  server 20.17.92.1 auth-port 1645 acct-port 1646
> >  authorization accept default ( added this
> command)
> > !
> > then 
> > radius-server attribute list default
> > 
> > and also added "calling-station-ID" attribute
> under
> > attribute list (Default the one created by above
> > command)
> > 
> > 
> > than also i cant see cisco uBR our NAS sending the
> > Calling-Station-ID to the radius server , 
> > 
> > i even tried doing this 
> > 
> > my-cmts02(config)#radius-server attribute ?
> >   11        Filter-Id attribute configuration
> >   188       Num-In-Multilink attribute
> configuration
> >   218       Address-Pool attribute
> >   32        NAS-Identifier attribute
> >   4         NAS IP address attribute
> >   44        Acct-Session-Id attribute
> >   6         Service-Type attribute
> >   69        Tunnel-Password attribute
> >   8         Framed IP address attribute
> >   list      List of Attribute Types
> >   nas-port  NAS-Port attribute configuration
> > 
> > 
> > but as u see there isnt any thing mentioned for
> > "calling-station-ID" (31)  so i was not able to
> > enable
> > it ,
> > 
> > 
> >   so if any one knows anything about this then
> > kindly
> > let me know what i am missing here ? what should i
> > do
> > to enable it so that it starts sending
> > calling-station-ID attribute? 
> > 
> > regards
> > Prashant
> > 
> > __________________________________
> > Do you Yahoo!?
> > The New Yahoo! Search - Faster. Easier. Bingo.
> > http://search.yahoo.com
> > _______________________________________________
> > cisco-ubr mailing list
> > cisco-ubr at puck.nether.net
> > http://puck.nether.net/mailman/listinfo/cisco-ubr
> 
> 
> __________________________________
> Do you Yahoo!?
> The New Yahoo! Search - Faster. Easier. Bingo.
> http://search.yahoo.com


__________________________________
Do you Yahoo!?
The New Yahoo! Search - Faster. Easier. Bingo.
http://search.yahoo.com


More information about the cisco-nas mailing list