[cisco-nas] Re: [c-ubr] Missing Calling-Station-ID in Access-Request

Adeel Ahmed adeel_373 at yahoo.com
Fri May 2 10:10:09 EDT 2003


I think you will need to configure the following
commands to get this working:

radius-server vsa send accounting                     
radius-server vsa send authentication


Take a look at the following example for reference:

http://www.cisco.com/en/US/partner/products/sw/iosswrel/ps1839/products_feature_guide_chapter09186a00800b5de5.html

Eventhough the example is not from a uBR7246 you can
see the NAS(AS5300) sending radius attribute 31 to the
radius-server.

Hope this helps !

Adeel.

--- Nilesh Naik <qmailindia at yahoo.com> wrote:
> Hi all 
> 
>   we rae using cisco uBR 7246, as our PPPoE
> concentrator and NAS , we are running IOS (tm) 7200
> Software (UBR7200-IK8S-M), Version 12.2(11)BC3,
> EARLY
> DEPLOYMENT RELEASE SOFTWARE (fc2)  on this uBR , 
> 
>    we are presently using the Radius Authentication
> for all the PPPoE dialin Users , but when i see in
> the
> debug mode by enabling "debug radius", debug aaa
> authentication" & "debug aaa accounting" i cant see
> cisco uBR sending "Calling-Station-Id" attribute to
> the radius , which i think sould contain value of
> the
> customer's MAC Address if i am correct ?? pls
> correct
> me if i am wrong here ? 
> 
>    now i check out every option on the Ubr to enable
> this i even tried these following commands 
> 
> aaa group server radius accountgroup
>  server 20.17.92.2 auth-port 1645 acct-port 1646
>  server 20.17.92.1 auth-port 1645 acct-port 1646
>  authorization accept default ( added this command)
> !
> then 
> radius-server attribute list default
> 
> and also added "calling-station-ID" attribute under
> attribute list (Default the one created by above
> command)
> 
> 
> than also i cant see cisco uBR our NAS sending the
> Calling-Station-ID to the radius server , 
> 
> i even tried doing this 
> 
> my-cmts02(config)#radius-server attribute ?
>   11        Filter-Id attribute configuration
>   188       Num-In-Multilink attribute configuration
>   218       Address-Pool attribute
>   32        NAS-Identifier attribute
>   4         NAS IP address attribute
>   44        Acct-Session-Id attribute
>   6         Service-Type attribute
>   69        Tunnel-Password attribute
>   8         Framed IP address attribute
>   list      List of Attribute Types
>   nas-port  NAS-Port attribute configuration
> 
> 
> but as u see there isnt any thing mentioned for
> "calling-station-ID" (31)  so i was not able to
> enable
> it ,
> 
> 
>   so if any one knows anything about this then
> kindly
> let me know what i am missing here ? what should i
> do
> to enable it so that it starts sending
> calling-station-ID attribute? 
> 
> regards
> Prashant
> 
> __________________________________
> Do you Yahoo!?
> The New Yahoo! Search - Faster. Easier. Bingo.
> http://search.yahoo.com
> _______________________________________________
> cisco-ubr mailing list
> cisco-ubr at puck.nether.net
> http://puck.nether.net/mailman/listinfo/cisco-ubr


__________________________________
Do you Yahoo!?
The New Yahoo! Search - Faster. Easier. Bingo.
http://search.yahoo.com


More information about the cisco-nas mailing list