[cisco-nas] RE: Re: Lucent XL connection

[Balgansuren]

Hi,

Thank you very much. Is there any low capacity solution to use Cisco
AS5300/AS5350 with C7 signaling?

I know Cisco has has solution for it (SC2200,PGW2200)and software price
too high for us.

Any suggestion?

Thank you,
Balgaa

> Your E1 is down; the other side is sending an alarm.
> 
> Start here: 
> E1 PRI Troubleshooting
>
http://www.cisco.com/en/US/tech/tk713/tk628/technologies_tech_note09186a00800a70fc.shtml
> 
> 
> Aaron
> 
> ---
> 
> > Hi,
> 
> > We are using Cisco AS5300/AS5350 with 4E1/8E1 lines
> gateway and R2
> > digitall signaling used to connect with Alcatel
> E10/Siemens EWSD voice
> > switch/PBX.
> 
> > And we are trying change configuration of Cisco
> AS5300/AS5350 using
> > ISDN PRI signaling with Lucent Excel switch.
> 
> > We done configuration on Lucent Excel switch using
> incoming
> > "EuroISDN", outgoing "ISDN IE".
> 
> > On Cisco side following:
> 
> > !
> > controller E1 2
> >  pri-group timeslots 1-31
> >  description Connected to Excel switch span 9
> > !
> 
> > !
> > interface Serial2:15
> >  no ip address
> >  isdn switch-type primary-net5
> >  isdn incoming-voice modem
> >  isdn send-alerting
> >  isdn sending-complete
> >  no cdp enable
> > !
> 
> > E1 line never get up:
> 
> > E1 2 is down.
> >   Applique type is Channelized E1 - balanced
> >   Description: Connected to Excel switch span 9
> >   Receiver has remote alarm.
> >   alarm-trigger is not set
> >   Version info of slot 0:  HW: 1, PLD Rev: 11
> >   Framer Version: 0x8
> 
> > Manufacture Cookie Info:
> >  EEPROM Type 0x0001, EEPROM Version 0x01, Board ID
> 0x4B,
> >  Board Hardware Version 3.1, Item Number
> 800-3881-02,
> >  Board Revision D31, Serial Number 27517409,
> >  PLD/ISP Version 0.1,  Manufacture Date
> 19-Dec-2001.
> 
> >   Framing is CRC4, Line Code is HDB3, Clock Source
> is Internal.
> >   Data in current interval (159 seconds elapsed):
> >      0 Line Code Violations, 0 Path Code Violations
> >      0 Slip Secs, 159 Fr Loss Secs, 0 Line Err
> Secs, 0 Degraded Mins
> >      0 Errored Secs, 0 Bursty Err Secs, 0 Severely
> Err Secs, 159
> > Unavail Secs
> >   Total Data (last 40 15 minute intervals):
> >      0 Line Code Violations, 0 Path Code
> Violations,
> >      0 Slip Secs, 583 Fr Loss Secs, 0 Line Err
> Secs, 0 Degraded Mins,
> >      0 Errored Secs, 0 Bursty Err Secs, 0 Severely
> Err Secs, 583
> > Unavail Secs
> 
> > Could you send helpful advice? Also I didn't find
> any good
> > configuration/troubleshooting document on Cisco
> web.
> 
> > Balgaa
> 
> 
> 
> 
>