[cisco-nas] NFAS / % Cannot access B-channel interfaces

[Mark Johnson]

At 10:37 AM 10/13/2003 -0400, Michael G. Jung wrote:
>5300 configured with NFAS, can not configure "Serial 1:23" or "Serial
>2:23"....
>
>This is my first time configuring NFAS. The switch tech indicates no
>errors on
>his side....  I just can't configure the b-channels for "controller T1
>1" or
>"controller T1 2"....

You only need to configure the primary NFAS interface; the others
will not be viewable, since the primary config extends to all NFAS
members.

http://www.cisco.com/warp/public/793/access_dial/quadt1_nfas.html

mark


>Any ideas anyone?????
>
>Thanks!
>
>---------------------- config b-channels ------------------
>
>c5300-1.uslec(config)#int serial 1:23
>% Cannot access B-channel interfaces
>c5300-1.uslec(config)#
>
>------------------- NFAS CONFIG --------------------------
>
>controller T1 0
>  framing esf
>  clock source line primary
>  linecode b8zs
>  pri-group timeslots 1-24 nfas_d primary nfas_int 1 nfas_group 1
>  description USLEC PRI T1/HCGS/07393/022/US
>!
>controller T1 1
>  framing esf
>  clock source line secondary 1
>  linecode b8zs
>  pri-group timeslots 1-24 nfas_d backup nfas_int 2 nfas_group 1
>  description USLEC PRI T1/HCGS/07394/022/US
>!
>controller T1 2
>  framing esf
>  clock source line secondary 2
>  linecode b8zs
>  pri-group timeslots 1-24 nfas_d none nfas_int 3 nfas_group 1
>  description USLEC PRI T1/HCGS/07395/022/US
>!
>
>------------------- NFAS STATUS ------------------------------
>
>c5300-1.uslec#show isdn nfas group 1
>
>          ISDN NFAS GROUP 1 ENTRIES:
>
>          The primary D is Serial0:23.
>          The backup D is Serial1:23.
>          The NFAS member is Serial2:23.
>
>          There are 3 total nfas members.
>          There are 70 total available B channels.
>          The primary D-channel is DSL 0 in state IN SERVICE
>          The backup D-channel is DSL 1 in state STANDBY
>          The current active layer 2 DSL is 0.
>c5300-1.uslec#
>
>------------------ Controller STATUS --------------------------
>
>c5300-1.uslec#show cont t1 1
>T1 1 is up.
>   Applique type is Channelized T1
>   Cablelength is long gain36 0db
>   Description: USLEC PRI T1/HCGS/07394/022/US
>   No alarms detected.
>   alarm-trigger is not set
>   Version info of slot 0:  HW: 1, PLD Rev: 11
>   Framer Version: 0x8
>
>Manufacture Cookie Info:
>  EEPROM Type 0x0001, EEPROM Version 0x01, Board ID 0x4A,
>  Board Hardware Version 3.1, Item Number 800-3881-02,
>  Board Revision B0, Serial Number 20746771,
>  PLD/ISP Version 0.1,  Manufacture Date 2-Jul-2000.
>
>   Framing is ESF, Line Code is B8ZS, Clock Source is Line Secondary.
>   Data in current interval (26 seconds elapsed):
>      0 Line Code Violations, 0 Path Code Violations
>      0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
>      0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail
>Secs
>c5300-1.uslec#
>
>Regards,
>
>Michael Jung
>Confluent Technologies
>11857 Commonwealth Drive
>Louisville, KY 40299
>502-212-4045 Work Voice
>
>_______________________________________________
>cisco-nas mailing list
>cisco-nas at puck.nether.net
>https://puck.nether.net/mailman/listinfo/cisco-nas