[cisco-nas] as5350 question

Sun Oct 26 10:51:28 EST 2003

We experienced something similar a few months ago but have upgraded to
12.3(1a) that runs SPE version 0.8.3.0 and not seeing any known issues.  We
did need to add the modemcap entry next:MSC=&FS0=0S29=6S21=3 and we have to
force GTW v.92 and Conexant v.92 modems to +ms=v90.  After 4 months of use we
know of no other troubles with this setup.

hope this may help in some way.

thanks

Greg

Cisco Internetwork Operating System Software
IOS (tm) 5350 Software (C5350-IS-M), Version 12.3(1a), RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2003 by cisco Systems, Inc.
Compiled Fri 06-Jun-03 09:17 by dchih
Image text-base: 0x6000895C, data-base: 0x61600000

ROM: System Bootstrap, Version 12.1(2r)XD1, RELEASE SOFTWARE (fc1)
BOOTLDR: 5350 Software (C5350-BOOT-M), Experimental Version
12.1(20000922:142008) [nag-flo_t_0110 101]

glasgow-as1 uptime is 9 weeks, 5 days, 4 hours, 21 minutes
System returned to ROM by reload at 05:23:55 MDT Tue Aug 19 2003
System restarted at 05:27:58 MDT Tue Aug 19 2003
System image file is "flash:c5350-is-mz.123-1a.bin"

cisco AS5350 (R7K) processor (revision T) with 131072K/65536K bytes of memory.

Processor board ID JAB04350AV5
R7000 CPU at 250Mhz, Implementation 39, Rev 1.0, 256KB L2, 2048KB L3 Cache
Last reset from IOS reload
Bridging software.
X.25 software, Version 3.0.0.
SuperLAT software (copyright 1990 by Meridian Technology Corp).
Primary Rate ISDN software, Version 1.1.
Manufacture Cookie Info:
 EEPROM Type 0x0001, EEPROM Version 0x01, Board ID 0x32,
 Board Hardware Version 3.27, Item Number 800-5171-01,
 Board Revision B0, Serial Number JAB04350AV5,
 PLD/ISP Version 2.2,  Manufacture Date 23-Aug-2000.
Processor 0x14, MAC Address 0x02B935C1CE
Backplane HW Revision 1.0, Flash Type 5V
2 FastEthernet/IEEE 802.3 interface(s)
54 Serial network interface(s)
60 terminal line(s)
2 Channelized T1/PRI port(s)
512K bytes of non-volatile configuration memory.
32768K bytes of processor board System flash (Read/Write)
8192K bytes of processor board Boot flash (Read/Write)

Configuration register is 0x2102

IOS-Bundled Default Firmware-Filename      Version        Firmware-Type
=====================================      ============   =============
system:/ucode/spe_firmware-1               0.8.3.0         SPE firmware

On-Flash Firmware-Filename                 Version        Firmware-Type
=====================================      ============   =============

  SPE-#   Type   Port-Range           Version   UPG Firmware-Filename
   1/00  CSMV6    0000-0005           0.8.3.0   N/A ios-bundled default
   1/01  CSMV6    0006-0011           0.8.3.0   N/A ios-bundled default
   1/02  CSMV6    0012-0017           0.8.3.0   N/A ios-bundled default
   1/03  CSMV6    0018-0023           0.8.3.0   N/A ios-bundled default
   1/04  CSMV6    0024-0029           0.8.3.0   N/A ios-bundled default
   1/05  CSMV6    0030-0035           0.8.3.0   N/A ios-bundled default
   1/06  CSMV6    0036-0041           0.8.3.0   N/A ios-bundled default
   1/07  CSMV6    0042-0047           0.8.3.0   N/A ios-bundled default
   1/08  CSMV6    0048-0053           0.8.3.0   N/A ios-bundled default
   1/09  CSMV6    0054-0059           0.8.3.0   N/A ios-bundled default

Lewis Watson wrote:

> I have seen this too. I am not sure under what conditions specifically but
> I have been told by users that they have to "give it a few seconds after
> it connects before they can use the Internet". I would like to know why
> too. Running  an AS5350 with 12.2 XB11 spe version is 7.18.3.
> Thanks.
> Lewis
>
> ----- Original Message -----
> From: "John McKinney" <johnm at wnconline.net>
> To: <cisco-nas at puck.nether.net>
> Sent: Saturday, October 25, 2003 9:24 PM
> Subject: [cisco-nas] as5350 question
>
> > We are having a strange problem, hopefully someone can offer some
> insite.
> >
> > AS5350
> > IOS 122-2.XB11
> >
> > PRI's setup for Dialup Internet Access
> >
> > Some users will authenticate (AAA/Radius) as normal, but once they log
> in
> > the first request will fail. Meaning, if they are connecting from a
> > windows computer using internet explorer, once the dialup connection is
> > established, the home page will not display. The system will pause for a
> > few seconds then IE will display an error about unable to find server.
> > If the user starts out by opening outlook express and connects, it will
> > also fail with a unable to find server message. It doesn't effect every
> > user and it does not happen at every connection. I tried changing one
> > users home page to an IP rather than a name and it stilled failed to
> find
> > the site. If the user clicks 'home' or 'send/recieve' everything will
> > work fine. I am not sure when the problem started, but it has been
> > happening for several months. Any ideas?
> >
> > Thank You,
> > John McKinney
> >
> >
> > _______________________________________________
> > cisco-nas mailing list
> > cisco-nas at puck.nether.net
> > https://puck.nether.net/mailman/listinfo/cisco-nas
> >
>
> _______________________________________________
> cisco-nas mailing list
> cisco-nas at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-nas