[cisco-nas] WIC-1B-S/T "L1 deactivated"

[Josh Duffek]

Doubtful that is the problem..unless you have a weird bug.  

What happens if you actually try to make a call though?  Doesn't europe
l1/l2 stuff stay down until needed?  Or is that just l2...can't
remember.

Is the NT1 set for 100ohm?  Debug isdn q921 won't show anything unless
your L1 is up..."debug bri" is what you want...although it is pretty
cryptic it will kinda let you know what is going on.

josh duffek    network engineer
consultantjd16 at ridemetro.org

> -----Original Message-----
> From: cisco-nas-bounces at puck.nether.net [mailto:cisco-nas-
> bounces at puck.nether.net] On Behalf Of furda at bgs.sk
> Sent: Wednesday, February 23, 2005 9:41 AM
> To: Daniel Roesen
> Cc: cisco-nas at puck.nether.net
> Subject: Re: [cisco-nas] WIC-1B-S/T "L1 deactivated"
> 
> Hi Daniel,
> 
> do you have the ISDN switch type configured globally? If not,
configure
> it.
> 
> Richard
> 
> Quoting Daniel Roesen <dr at cluenet.de>:
> > Hi,
> >
> > I'm giving up (and now ask here). I'm trying to do some very basic
> > DDR using a 3640 with WIC-1B-S/T on NM-2E2W:
> >
> > Slot 3:
> >         Combo 2E, 2W Port adapter, 4 ports
> > ...
> >         WIC Slot 1:
> >         BRI S/T - 2186 WAN daughter card
> >         Hardware revision 1.3           Board revision A0
> >         Serial number     10368460      Part number    800-01833-02
> >         Test history      0x0           RMA number     00-00-00
> >         Connector type    Wan Module
> > ...
> >
> > interface BRI3/0
> >  no ip address
> >  encapsulation ppp
> >  dialer map ip 192.168.17.1 123456
> >  dialer-group 3
> >  isdn switch-type basic-net3
> >  ppp authentication chap
> > end
> >
> > but:
> >
> > ISDN BRI3/0 interface
> >         dsl 24, interface ISDN Switchtype = basic-net3
> >     Layer 1 Status:
> >         DEACTIVATED
> >     Layer 2 Status:
> >         Layer 2 NOT Activated
> >     Layer 3 Status:
> >         0 Active Layer 3 Call(s)
> >     Active dsl 24 CCBs = 0
> >     The Free Channel Mask:  0x80000003
> >     Total Allocated ISDN CCBs = 0
> >
> > "deb isdn q921" and shut/noshut did give no debug info at all.
> >
> > Cisco IOS Software, 3600 Software (C3640-JS-M), Version 12.3(8)T6,
> > RELEASE SOFTWARE (fc2)
> >
> > I swapped cables, plugged the WIC directly into the NT, and even
used
> > another router (2621) with a different WIC-1B-S/T without success:
> >
> > IOS (tm) C2600 Software (C2600-IK9O3S3-M), Version 12.3(12), RELEASE
> > SOFTWARE (fc3)
> >
> > What am I doing wrong? Other devices like an ISDN phone work
flawlessly
> > on the same S0 bus.
> >
> >
> > Best regards,
> > Daniel
> >
> > --
> > CLUE-RIPE -- Jabber: dr at cluenet.de -- dr at IRCnet -- PGP: 0xA85C8AA0
> > _______________________________________________
> > cisco-nas mailing list
> > cisco-nas at puck.nether.net
> > https://puck.nether.net/mailman/listinfo/cisco-nas
> >
> 
> 
> --
> _______________________________________________
> cisco-nas mailing list
> cisco-nas at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-nas