[nsp] 12.2.2XB8 line/modem/controller-t1 numbering
Brian Roberson
roberson@olug.org
Mon, 25 Nov 2002 18:09:25 -0600
This is a multi-part message in MIME format.
------=_NextPart_000_000B_01C294AD.CA2F5D70
Content-Type: text/plain;
charset="iso-8859-1"
Content-Transfer-Encoding: quoted-printable
as5300, two CAS t1's=20
how can I ensure calls on controller 0 only use tty lines 1-24 ; and =
controller 1 use tty lines 25-48?
example config:
...
!
controller T1 0
framing esf
linecode b8zs
ds0-group 0 timeslots 1-24 type e&m-fgb dtmf dnis
description T1-1
!
controller T1 1
framing esf
linecode b8zs
ds0-group 1 timeslots 1-24 type e&m-fgb dtmf dnis
description T1-2
!
....
line 1 24
exec-timeout 0 0
modem Dialin
modem autoconfigure type mica
autocommand telnet HOST1 PORT1 /quiet /stream
terminal-type vt100
exec-character-bits 8
length 80
escape-character NONE
telnet transparent
line 25 48
exec-timeout 0 0
modem Dialin
modem autoconfigure type pdx
autocommand telnet HOST2 PORT2 /stream /quiet
terminal-type vt100
exec-character-bits 8
length 80
escape-character NONE
telnet transparent
!
!
What I would expect is lines 1-24 would be controller t1 0 and 25-48 =
would controller t1 1, this is not necisarily the case.
oma-async01#sh line 1
Tty Typ Tx/Rx A Modem Roty AccO AccI Uses Noise Overruns =
Int
1 TTY - DialIn - - - 0 0 0/0 =
-
Line 1, Location: "", Type: "vt100"
Length: 80 lines, Width: 80 columns
Status: No Exit Banner, Modem Detected, CTS Raised
Capabilities: Telnet Transparent Mode, Hardware Flowcontrol In
Hardware Flowcontrol Out, Modem RI is CD, Modem Autoconfigure
Integrated Modem
Modem state: Idle
modem(slot/port)=3D1/0, state=3DIDLE
dsx1(slot/unit/channel)=3DNONE, status=3DVDEV_STATUS_UNLOCKED
Modem hardware state: CTS noDSR DTR RTS, Modem Configured
Special Chars: Escape Hold Stop Start Disconnect Activation
none none - - none
Timeouts: Idle EXEC Idle Session Modem Answer Session =
Dispatch
never never none not =
set
Idle Session Disconnect Warning
never
Login-sequence User Response
00:00:30
Autoselect Initial Wait
not set
Modem type is pdx.
Session limit is not set.
Time since activation: never
Editing is enabled.
History is enabled, history size is 10.
DNS resolution in show commands is enabled
Full user help is disabled
Allowed input transports are none.
Allowed output transports are pad telnet rlogin.
Preferred transport is telnet.
Automatically execute command "telnet HOST1 PORT1 /stream /quiet"
No output characters are padded
No special data dispatching characters
router#
......
------=_NextPart_000_000B_01C294AD.CA2F5D70
Content-Type: text/html;
charset="iso-8859-1"
Content-Transfer-Encoding: quoted-printable
<!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.0 Transitional//EN">
<HTML><HEAD>
<META http-equiv=3DContent-Type content=3D"text/html; =
charset=3Diso-8859-1">
<META content=3D"MSHTML 6.00.2800.1106" name=3DGENERATOR>
<STYLE></STYLE>
</HEAD>
<BODY bgColor=3D#ffffff>
<DIV><FONT face=3DArial size=3D2>as5300, two CAS t1's </FONT></DIV>
<DIV><FONT face=3DArial size=3D2>how can I ensure calls on controller 0=20
only use tty lines 1-24 ; and controller 1 use tty lines=20
25-48?</FONT></DIV>
<DIV><FONT face=3DArial size=3D2></FONT> </DIV>
<DIV><FONT face=3DArial size=3D2>example config:</FONT></DIV>
<DIV><FONT face=3DArial size=3D2></FONT> </DIV>
<DIV><FONT face=3DArial size=3D2>...</FONT></DIV>
<DIV><FONT face=3DArial size=3D2>!</FONT></DIV>
<DIV><FONT face=3DArial size=3D2>controller T1 0<BR> framing=20
esf<BR> linecode b8zs<BR> ds0-group 0 timeslots 1-24 type =
e&m-fgb=20
dtmf dnis<BR> description T1-1<BR>!<BR>controller T1 =
1<BR> framing=20
esf<BR> linecode b8zs<BR> ds0-group 1 timeslots 1-24 type =
e&m-fgb=20
dtmf dnis<BR> description T1-2<BR>!<BR></FONT><FONT face=3DArial=20
size=3D2>....</FONT></DIV>
<DIV><FONT face=3DArial size=3D2>line 1 24<BR> exec-timeout 0 =
0<BR> modem=20
Dialin<BR> modem autoconfigure =
type mica<BR> autocommand =20
telnet HOST1 PORT1 /quiet /stream<BR> terminal-type=20
vt100<BR> exec-character-bits 8<BR> length=20
80<BR> escape-character NONE<BR> telnet transparent<BR>line 25 =
48<BR> exec-timeout 0 0<BR> modem Dialin<BR> modem =
autoconfigure=20
type pdx<BR> autocommand telnet HOST2 PORT2 /stream =
/quiet<BR> terminal-type vt100<BR> exec-character-bits=20
8<BR> length 80<BR> escape-character NONE<BR> telnet=20
transparent<BR>!</FONT></DIV>
<DIV><FONT face=3DArial size=3D2>!</FONT></DIV>
<DIV><FONT face=3DArial size=3D2> </DIV></FONT>
<DIV><FONT face=3DArial size=3D2></FONT> </DIV>
<DIV><FONT face=3DArial size=3D2></FONT> </DIV>
<DIV><FONT face=3DArial size=3D2></FONT> </DIV>
<DIV><FONT face=3DArial size=3D2></FONT> </DIV>
<DIV><FONT face=3DArial size=3D2>What I would expect is lines 1-24 would =
be=20
controller t1 0 and 25-48 would controller t1 1, this is not necisarily =
the=20
case.</FONT></DIV>
<DIV><FONT face=3DArial size=3D2></FONT> </DIV>
<DIV><FONT face=3DArial size=3D2></FONT> </DIV>
<DIV><FONT face=3DArial size=3D2>oma-async01#sh line 1<BR> =
Tty=20
Typ Tx/Rx A Modem Roty =
AccO=20
AccI Uses Noise Overruns =20
Int<BR> 1=20
TTY &nbs=
p; =20
- DialIn - - =20
- 0 =20
0 0/0 =
-</FONT></DIV>
<DIV><FONT face=3DArial size=3D2></FONT> </DIV>
<DIV><FONT face=3DArial size=3D2>Line 1, Location: "", Type: =
"vt100"<BR>Length: 80=20
lines, Width: 80 columns<BR>Status: No Exit Banner, Modem Detected, CTS=20
Raised<BR>Capabilities: Telnet Transparent Mode, Hardware Flowcontrol=20
In<BR> Hardware Flowcontrol Out, Modem RI is CD, Modem=20
Autoconfigure<BR> Integrated Modem<BR>Modem state: Idle<BR> =20
modem(slot/port)=3D1/0, state=3DIDLE<BR> =
dsx1(slot/unit/channel)=3DNONE,=20
status=3DVDEV_STATUS_UNLOCKED<BR>Modem hardware state: CTS noDSR =
DTR RTS,=20
Modem Configured<BR>Special Chars: Escape Hold Stop =20
Start Disconnect =20
Activation<BR>  =
; =20
none none - =20
- =20
none<BR>Timeouts: Idle =
EXEC Idle=20
Session Modem Answer Session =20
Dispatch<BR> &=
nbsp; =20
never =20
never &n=
bsp; =20
none not=20
set<BR> =
&=
nbsp; =20
Idle Session Disconnect=20
Warning<BR> &n=
bsp; &nb=
sp; =20
never<BR> &nbs=
p;  =
; =20
Login-sequence User=20
Response<BR> &=
nbsp; &n=
bsp; =20
00:00:30<BR> &=
nbsp; &n=
bsp; =20
Autoselect Initial=20
Wait<BR>  =
; =
=20
not set<BR>Modem type is pdx.<BR>Session limit is not set.<BR>Time since =
activation: never<BR>Editing is enabled.<BR>History is enabled, history =
size is=20
10.<BR>DNS resolution in show commands is enabled<BR>Full user help is=20
disabled<BR>Allowed input transports are none.<BR>Allowed output =
transports are=20
pad telnet rlogin.<BR>Preferred transport is telnet.<BR>Automatically =
execute=20
command "telnet HOST1 PORT1 /stream /quiet"<BR>No output characters are=20
padded<BR>No special data dispatching =
characters<BR>router#<BR></FONT></DIV>
<DIV><FONT face=3DArial size=3D2></FONT> </DIV>
<DIV><FONT face=3DArial size=3D2></FONT> </DIV>
<DIV><FONT face=3DArial size=3D2></FONT> </DIV>
<DIV><FONT face=3DArial size=3D2></FONT> </DIV>
<DIV><FONT face=3DArial size=3D2></FONT> </DIV>
<DIV><FONT face=3DArial size=3D2></FONT> </DIV>
<DIV><FONT face=3DArial size=3D2></FONT> </DIV>
<DIV><FONT face=3DArial size=3D2>......</FONT></DIV></BODY></HTML>
------=_NextPart_000_000B_01C294AD.CA2F5D70--