[nsp] to tell WIC-2T from WIC-2A/S
Scott.Keoseyan@BroadWing.com
Scott.Keoseyan@BroadWing.com
Fri, 20 Sep 2002 11:31:12 -0500
Victor...
here is the output from a 2611 I have... Slot0 is considered the 'chassis'
slot, or the slot where the fixed configuration LAN ports and WIC slots
reside.
So here in slot0 we have the mainboard and a WIC-2T in WIC-Slot0 of Chassis
slot0 and a WIC-1B-U in WIC-Slot1 of chassis slot0.
router#sh diag
Slot 0:
C2611 2E Mainboard Port adapter, 5 ports
Port adapter is analyzed
Port adapter insertion time unknown
EEPROM contents at hardware discovery:
Hardware Revision : 2.2
PCB Serial Number : JAB031003DZ (1459886166)
Part Number : 73-2840-11
RMA History : 00
RMA Number : 0-0-0-0
Board Revision : A0
Deviation Number : 0-0
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF 40 00 92 41 02 02 C1 18 4A 41 42 30 33 31
0x10: 30 30 33 44 5A 20 28 31 34 35 39 38 38 36 31 36
0x20: 36 29 82 49 0B 18 0B 04 00 81 00 00 00 00 42 41
0x30: 30 80 00 00 00 00 FF FF FF FF FF FF FF FF FF FF
0x40: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
WIC Slot 0: ---->(Serial 0/0 and 0/1)
Serial 2T (12in1) WAN daughter card
Hardware revision 1.0 Board revision B0
Serial number 14845267 Part number 800-03181-01
Test history 0x0 RMA number 00-00-00
Connector type PCI
EEPROM format version 1
EEPROM contents (hex):
0x20: 01 12 01 00 00 E2 85 53 50 0C 6D 01 00 00 00 00
0x30: 58 00 00 00 99 06 30 00 FF FF FF FF FF FF FF FF
WIC Slot 1: ---->(Bri 0/0)
BRI U - 2091 WAN daughter card
Hardware revision 4.0 Board revision B0
Serial number 11996524 Part number 800-01834-02
Test history 0x0 RMA number 00-00-00
Connector type Wan Module
EEPROM format version 1
EEPROM contents (hex):
0x20: 01 09 04 00 00 B7 0D 6C 50 07 2A 02 00 00 00 00
0x30: 58 00 00 00 99 01 23 01 FF FF FF FF FF FF FF FF
If there was another WIC2T in WIC Slot1, then it would have Ser0/2 and
Ser0/3 in it:
Here is the output from a 2612 with two WIC-2T cards...
Slot 0:
C2612 1E1R Mainboard Port adapter, 6 ports
Port adapter is analyzed
Port adapter insertion time unknown
EEPROM contents at hardware discovery:
Hardware Revision : 1.1
PCB Serial Number : JAB030203SZ (2638101857)
Part Number : 73-2841-07
RMA History : 00
RMA Number : 0-0-0-0
Board Revision : A0
Deviation Number : 0-0
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF 40 00 93 41 01 01 C1 18 4A 41 42 30 33 30
0x10: 32 30 33 53 5A 20 28 32 36 33 38 31 30 31 38 35
0x20: 37 29 82 49 0B 19 07 04 00 81 00 00 00 00 42 41
0x30: 30 80 00 00 00 00 FF FF FF FF FF FF FF FF FF FF
0x40: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
WIC Slot 0: --->(Ser0/0 and Ser0/1)
Serial 2T (12in1) WAN daughter card
Hardware revision 1.0 Board revision A0
Serial number 12811749 Part number 800-03181-01
Test history 0x0 RMA number 00-00-00
Connector type PCI
EEPROM format version 1
EEPROM contents (hex):
0x20: 01 12 01 00 00 C3 7D E5 50 0C 6D 01 00 00 00 00
0x30: 50 00 00 00 99 02 28 00 FF FF FF FF FF FF FF FF
WIC Slot 1: --->(Ser0/2 and Ser0/3)
Serial 2T (12in1) WAN daughter card
Hardware revision 1.0 Board revision A0
Serial number 12811361 Part number 800-03181-01
Test history 0x0 RMA number 00-00-00
Connector type PCI
EEPROM format version 1
EEPROM contents (hex):
0x20: 01 12 01 00 00 C3 7C 61 50 0C 6D 01 00 00 00 00
0x30: 50 00 00 00 99 02 26 00 FF FF FF FF FF FF FF FF
Down here in Slot1, the network module slot, we have a NM-2V... Slot1 is the
Network Module slot on a 2600.
Slot 1:
4 PORT Voice PM for C2600 Port adapter
Port adapter is disabled
Port adapter insertion time unknown
EEPROM contents at hardware discovery:
Hardware revision 1.1 Board revision H0
Serial number 18743476 Part number 800-02491-02
Test history 0x0 RMA number 00-00-00
EEPROM format version 1
EEPROM contents (hex):
0x20: 01 65 01 01 01 1E 00 B4 50 09 BB 02 00 00 00 00
0x30: 88 00 00 00 00 03 15 17 FF FF FF FF FF FF FF FF
Scott
> -----Original Message-----
> From: Victor Sudakov [mailto:sudakov@sibptus.tomsk.ru]
> Sent: Friday, September 20, 2002 12:07 PM
> To: Jared Mauch
> Cc: cisco-nsp@puck.nether.net; AGRANDMO@mail.mobistar.be
> Subject: Re: [nsp] to tell WIC-2T from WIC-2A/S
>
>
> Jared Mauch wrote:
> > Try 'sh diag'
>
> I did but I do not understand how a slot number relates to a logical
> serial interface number. Say, "Serial0/3" is in what slot?
>
> > >
> > > There are a WIC-2T and a WIC-2A/S modules in a c2610.
> Their interfaces
> > > are visible as Serial0/0 to Serial0/3. Is there a way to
> tell whether
> > > a particular interface belongs to a WIC-2T card or to a
> WIC-2A/S card?
> > > The "show controller" output for all the four interfaces seems
> > > identical.
> > >
> > > Thanks a lot for any input.
>
> --
> Victor Sudakov, VAS4-RIPE, VAS47-RIPN
> _______________________________________________
> cisco-nsp mailing list real_name)s@puck.nether.net
> http://puck.nether.net/mailman/listinfo/cisco-nsp
> archive at http://puck.nether.net/pipermail/cisco-nsp/
>
+++The information transmitted is intended only for the person or entity to
which it is addressed and may contain confidential and/or privileged
material. Any review, retransmission, dissemination or other use of, or
taking of any action in reliance upon, this information by persons or
entities other than the intended recipient is prohibited. If you received
this in error, please contact the sender and destroy any copies of this
document.+++