[nsp] Newbie Question: Wic-2t on 3640 running IOS 12.3

[Vincent De Keyzer]

Well, the problem does not seem to come from the WIC but from the NM, right?

        NM-2FE2W Port adapter, 2 ports
        Port adapter is disabled <-------------

On a working router (2621 with NM-2W in slot 1 and 2 x VWIC-2MFT-E1):

Slot 1:
        NM-2W Port adapter, 4 ports
        Port adapter is analyzed <-----------------------
        Port adapter insertion time unknown

And further:

        WIC Slot 0:
        E1 (2 Port) Multi-Flex Trunk WAN Daughter Card

Etc.

But it's still weird that the FastEthernet interfaces appear... Are they
working? 

According to CCO
- the NM-2FE2W requires 12.0(7)XK, 12.1(1)T, 12.1(5)YB, 12.1(5)YD, 12.2(1),
12.2(2)T, 12.2(2)XT, 12.2(11)YT, 12.2(15)ZJ, 12.3(1)
- the WIC-2T requires 12.0(7)XK, 12.1(1)T, 12.1(5)YB, 12.1(5)YD, 12.2(1),
12.2(2)T, 12.2(2)XT, 12.2(11)YT, 12.2(15)ZJ, 12.3(1)
... So it should work with 12.3... Bug?

Vincent


> -----Original Message-----
> From: cisco-nsp-bounces at puck.nether.net 
> [mailto:cisco-nsp-bounces at puck.nether.net] On Behalf Of Santa Klaus
> Sent: jeudi 20 novembre 2003 22:51
> To: cisco-nsp at puck.nether.net
> Subject: [nsp] Newbie Question: Wic-2t on 3640 running IOS 12.3
> 
> 
> Hi,
>  
> I have a Cisco 3640 which i just bought from ebay. The router 
> has 12.3 IOS loaded on it. 
> I bought a WIC-2T from another person. Now the Wic-2T doesnt 
> seem to be getting detected by the Router. Show diag gives 
> the following:
> 
>         NM-2FE2W Port adapter, 2 ports (Could someone explain 
> this and the next line pls. Is the Module itself at fault?)
>         Port adapter is disabled
>         Port adapter insertion time unknown
>         EEPROM contents at hardware discovery:
>         Hardware Revision        : 1.0
>         Top Assy. Part Number    : 800-04797-01
>         Board Revision           : E0
>         Deviation Number         : 0-0
>         Fab Version              : 04
>         PCB Serial Number        : JAD06220LKQ
>         RMA Test History         : 00
>         RMA Number               : 0-0-0-0
>         RMA History              : 00
>         EEPROM format version 4
>         EEPROM contents (hex):
>           0x00: 04 FF 40 00 D8 41 01 00 C0 46 03 20 00 12 BD 01
>           0x10: 42 45 30 80 00 00 00 00 02 04 C1 8B 4A 41 44 30
>           0x20: 36 32 32 30 4C 4B 51 03 00 81 00 00 00 00 04 00
>           0x30: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
>           
> What might be the problem? I tried removing and reinserting 
> the card, to no avail. Is the card bad? Could I have the 
> wrong IOS? Will it work with 12.2? I have 12.3 now, 
> currently. The wic-2t compatability listing does not 
> explicitly list 12.3, thats why Im asking. 
>  
> Just want to make sure that it isnt something other than just 
> the card being a dud. 
> Show interface displays the fastethernet0/0 and 0/1 
> interfaces but not the serials. Thanks in advance.
> 
> 
> ---------------------------------
> Do you Yahoo!?
> Free Pop-Up Blocker - Get it now 
> _______________________________________________
> cisco-nsp mailing list  cisco-nsp at puck.nether.net 
> https://puck.nether.net/mailman/listinfo/cisco> -nsp
> archive at 
> http://puck.nether.net/pipermail/cisco-nsp/
>