[c-nsp] New to CCNA [ My first router 2501 :) ]

[Adrian Pirciu]

Hello

This URL should help you. 

http://www.cisco.com/en/US/products/hw/routers/ps133/products_tech_note09186a008020b19e.shtml

in short, you should issue "no service config" in global configuration 
mode. It is trying something called "autoconfiguration".


On Friday 30 July 2004 14:23, Huzaifah Ahmed wrote:
> Hello everybody,
>
> As you see I am new to Cisco and this is my first official post to
> this list. :) I recently purchased a router from ebay and I am a
> lill un sure of the errors shown below.
>
> Can anyone advise me how to get rid of them. Will highly appreciate
> your help.
>
> Thank you in advance.
>
> ------------------ show version ------------------
> Cisco Internetwork Operating System Software
> IOS (tm) 2500 Software (C2500-I-L), Version 12.0(14), RELEASE
> SOFTWARE (fc1) Copyright (c) 1986-2000 by cisco Systems, Inc.
> Compiled Tue 31-Oct-00 23:59 by linda
> Image text-base: 0x0302F438, data-base: 0x00001000
> ROM: System Bootstrap, Version 11.0(10c), SOFTWARE
> BOOTFLASH: 3000 Bootstrap Software (IGS-BOOT-R), Version 11.0(10c),
> RELEASE SOFT WARE (fc1)
> 2501A uptime is 4 hours, 4 minutes
> System restarted by power-on
> System image file is "flash:c2500-i-l.120-14"
> cisco 2500 (68030) processor (revision N) with 6144K/2048K bytes of
> memory. Processor board ID 26586640, with hardware revision
> 00000000 Bridging software.
> X.25 software, Version 3.0.0.
> 1 Ethernet/IEEE 802.3 interface(s)
> 2 Serial network interface(s)
> 32K bytes of non-volatile configuration memory.
> 8192K bytes of processor board System flash (Read ONLY)
> Configuration register is 0x2102
> -------------------------------- RELOAD COMMAND
> --------------------- Proceed with reload? [confirm]
> 04:21:56: %SYS-5-RELOAD: Reload requested
> System Bootstrap, Version 11.0(10c), SOFTWARE
> Copyright (c) 1986-1996 by cisco Systems
> 2500 processor with 6144 Kbytes of main memory
> %SYS-4-CONFIG_NEWER: Configurations from version 12.0 may not be
> correctly under stood.
> F3: 5656044+80240+423840 at 0x3000060
>
> A LOT OF OTHER STUFF .................
>
> cisco 2500 (68030) processor (revision N) with 6144K/2048K bytes of
> memory. Processor board ID 26586640, with hardware revision
> 00000000 Bridging software.
> X.25 software, Version 3.0.0.
> 1 Ethernet/IEEE 802.3 interface(s)
> 2 Serial network interface(s)
> 32K bytes of non-volatile configuration memory.
> 8192K bytes of processor board System flash (Read ONLY)
> %Error opening tftp://255.255.255.255/network-confg (Timed out)
> %Error opening tftp://255.255.255.255/cisconet.cfg (Timed out)
> %Error opening tftp://255.255.255.255/2501a-confg (Timed out)
> %Error opening tftp://255.255.255.255/2501a.cfg (Timed out)
>
> Press RETURN to get started!
>
> 00:00:21: %LINK-3-UPDOWN: Interface Ethernet0, changed state to up
> 00:00:21: %LINK-3-UPDOWN: Interface Serial0, changed state to down
> 00:00:21: %LINK-3-UPDOWN: Interface Serial1, changed state to down
> 00:00:22: %LINEPROTO-5-UPDOWN: Line protocol on Interface
> Ethernet0, changed sta te to down
> 00:00:22: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0,
> changed state to down
> 00:00:22: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1,
> changed state to down
> 00:00:26: %SYS-5-CONFIG_I: Configur
> 2501A>
> -------------------------------------------------------------------
>------------ These errors come in If I leave the router connection
> on console idle for a long time.
>
> 2501A#
> 2501A#
> %Error opening tftp://255.255.255.255/network-confg (Timed out)
> %Error opening tftp://255.255.255.255/cisconet.cfg (Timed out)
> %Error opening tftp://255.255.255.255/2501a-confg (Timed out)
> %Error opening tftp://255.255.255.255/2501a.cfg (Timed out)
> 2501A#
>
> Huzaif Ahmed
> _______________________________________________
> cisco-nsp mailing list  cisco-nsp at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-nsp
> archive at http://puck.nether.net/pipermail/cisco-nsp/

-- 
adixor