[c-nsp] New to CCNA [ My first router 2501 :) ]

[Rodney Dunn]

config t
no service config
end

On Fri, Jul 30, 2004 at 12:23:05PM +0100, Huzaifah Ahmed wrote:
> Hello everybody,
> 
> As you see I am new to Cisco and this is my first official post to this list. :) I recently purchased a router from ebay and I am a lill un sure of the errors shown below.
> 
> Can anyone advise me how to get rid of them. Will highly appreciate your help.
> 
> Thank you in advance.
> 
> ------------------ show version ------------------
> Cisco Internetwork Operating System Software
> IOS (tm) 2500 Software (C2500-I-L), Version 12.0(14), RELEASE SOFTWARE (fc1)
> Copyright (c) 1986-2000 by cisco Systems, Inc.
> Compiled Tue 31-Oct-00 23:59 by linda
> Image text-base: 0x0302F438, data-base: 0x00001000
> ROM: System Bootstrap, Version 11.0(10c), SOFTWARE
> BOOTFLASH: 3000 Bootstrap Software (IGS-BOOT-R), Version 11.0(10c), RELEASE SOFT
> WARE (fc1)
> 2501A uptime is 4 hours, 4 minutes
> System restarted by power-on
> System image file is "flash:c2500-i-l.120-14"
> cisco 2500 (68030) processor (revision N) with 6144K/2048K bytes of memory.
> Processor board ID 26586640, with hardware revision 00000000
> Bridging software.
> X.25 software, Version 3.0.0.
> 1 Ethernet/IEEE 802.3 interface(s)
> 2 Serial network interface(s)
> 32K bytes of non-volatile configuration memory.
> 8192K bytes of processor board System flash (Read ONLY)
> Configuration register is 0x2102
> -------------------------------- RELOAD COMMAND ---------------------
> Proceed with reload? [confirm]
> 04:21:56: %SYS-5-RELOAD: Reload requested
> System Bootstrap, Version 11.0(10c), SOFTWARE
> Copyright (c) 1986-1996 by cisco Systems
> 2500 processor with 6144 Kbytes of main memory
> %SYS-4-CONFIG_NEWER: Configurations from version 12.0 may not be correctly under
> stood.
> F3: 5656044+80240+423840 at 0x3000060
> 
> A LOT OF OTHER STUFF .................
> 
> cisco 2500 (68030) processor (revision N) with 6144K/2048K bytes of memory.
> Processor board ID 26586640, with hardware revision 00000000
> Bridging software.
> X.25 software, Version 3.0.0.
> 1 Ethernet/IEEE 802.3 interface(s)
> 2 Serial network interface(s)
> 32K bytes of non-volatile configuration memory.
> 8192K bytes of processor board System flash (Read ONLY)
> %Error opening tftp://255.255.255.255/network-confg (Timed out)
> %Error opening tftp://255.255.255.255/cisconet.cfg (Timed out)
> %Error opening tftp://255.255.255.255/2501a-confg (Timed out)
> %Error opening tftp://255.255.255.255/2501a.cfg (Timed out)
> 
> Press RETURN to get started!
> 
> 00:00:21: %LINK-3-UPDOWN: Interface Ethernet0, changed state to up
> 00:00:21: %LINK-3-UPDOWN: Interface Serial0, changed state to down
> 00:00:21: %LINK-3-UPDOWN: Interface Serial1, changed state to down
> 00:00:22: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0, changed sta
> te to down
> 00:00:22: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0, changed state
>  to down
> 00:00:22: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1, changed state
>  to down
> 00:00:26: %SYS-5-CONFIG_I: Configur
> 2501A>
> -------------------------------------------------------------------------------
> These errors come in If I leave the router connection on console idle for a long time.
> 
> 2501A#
> 2501A#
> %Error opening tftp://255.255.255.255/network-confg (Timed out)
> %Error opening tftp://255.255.255.255/cisconet.cfg (Timed out)
> %Error opening tftp://255.255.255.255/2501a-confg (Timed out)
> %Error opening tftp://255.255.255.255/2501a.cfg (Timed out)
> 2501A#
> 
> Huzaif Ahmed 
> _______________________________________________
> cisco-nsp mailing list  cisco-nsp at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-nsp
> archive at http://puck.nether.net/pipermail/cisco-nsp/