[nsp] Cisco Crashing

[Anson Rinesmith]

Do you mean after the reboot, or just before? If you are wanting before,
that might be hard to get, as it sometimes crashes in 1-2 minutes, sometimes
as long as 10 minutes.

> -----Original Message-----
> From: james at thehamptonfamily.us [mailto:james at thehamptonfamily.us]
> Sent: Wednesday, June 09, 2004 8:48 AM
> To: anson at bigrivertel.net
> Cc: cisco-nsp at puck.nether.net
> Subject: Re: [nsp] Cisco Crashing
> 
> What does a show stack give you when this happens?
> 
> James
> 
> > I have a 7206, with a 2 port Fast Ethernet Card, and an 8 port T1 card.
> >
> > I have my backhaul going out port F0/0, and I have T1's hooked up to the
> > 8 port card.
> >
> > The problem is, I am trying to add a Paradyne DSLAM to the F0/1 port.
> >
> > Within minutes of plugging in the Ethernet cable, my router goes into
> > cyclic rebooting.
> >
> > I get this in my crashinfo
> >
> > CMD: 'no crypto map NiStTeSt1' 11:39:42 UTC Wed May 26 2004
> >
> >
> >
> > CMD: 'no crypto map NiStTeSt1' 11:39:42 UTC Wed May 26 2004
> >
> >
> >
> > *May 26 11:39:43.316: %SYS-5-RESTART: System restarted --
> >
> > Cisco Internetwork Operating System Software
> >
> > IOS (tm) 7200 Software (C7200-IK9S-M), Version 12.3(3), RELEASE SOFTWARE
> > (fc2)
> >
> > Copyright (c) 1986-2003 by cisco Systems, Inc.
> >
> > Compiled Mon 18-Aug-03 21:11 by dchih
> >
> > *May 26 11:39:43.320: %SNMP-5-COLDSTART: SNMP agent on host nexus5 is
> > undergoing a cold start
> >
> > *May 26 11:39:43.916: %SYS-6-BOOTTIME: Time taken to reboot after reload
> > 157 seconds
> >
> > *May 26 11:39:44.184: %LINK-3-UPDOWN: Interface FastEthernet1/0, changed
> > state to up
> >
> > *May 26 11:39:44.184: %LINK-3-UPDOWN: Interface FastEthernet1/1, changed
> > state to up
> >
> > *May 26 11:39:44.204: %SSH-5-ENABLED: SSH 1.5 has been enabled
> >
> > *May 26 11:39:46.184: %LINEPROTO-5-UPDOWN: Line protocol on Interface
> > FastEthernet1/0, changed state to up
> >
> > *May 26 11:39:47.076: %LINEPROTO-5-UPDOWN: Line protocol on Interface
> > FastEthernet1/1, changed state to up
> >
> > %ERR-1-SERR: PCI bus system/parity error
> >
> >
> >
> > I've reseated all the cards, but it still happens. Where do I start?
> >
> >
> >
> > Anson Rinesmith
> >
> >
> >
> >
> >
> > _______________________________________________
> > cisco-nsp mailing list  cisco-nsp at puck.nether.net
> > https://puck.nether.net/mailman/listinfo/cisco-nsp
> > archive at http://puck.nether.net/pipermail/cisco-nsp/
>