[nsp] Maximum 2 MBPs Serial Ports in the 2610

[Fast Track Technologies]

Mark,

Pls check this: http://www.cisco.com/warp/public/107/nm-fe2w.html

Regards
Sunil

----- Original Message -----
From: "Mark Tinka" <mtinka at africaonline.co.sz>
To: "'Fast Track Technologies'" <fast_track at vsnl.com>;
<cisco-nsp at puck.nether.net>
Sent: Thursday, March 25, 2004 2:14 AM
Subject: RE: [nsp] Maximum 2 MBPs Serial Ports in the 2610


> Fast Track Technologies wrote:
> > Thanks Mark,
> >
> > As I understand the 2610 does not support the NM-1FE2W / NM-2FE2W..
>
> That's strange, I could swear the NM-1FE2W, NM-2FE2W, NM-1FE1R2W, and
NM-2W
> are supported by the 2600 series. IIRC, the new NM-1FE2W-V2 and
NM-2FE2W-V2
> modules are also supported, if you have the minimum IOS/RAM required.
>
> The 2600 series should swallow the NM-xFE2W module - but your minimum IOS
> version would have to be 12.0(7)XK with 32MB DRAM minimum. Any IOS
> featureset will do.
>
> >
> > Regards
> > Sunil
> >
> > ----- Original Message -----
> > From: "Mark Tinka" <mtinka at africaonline.co.sz>
> > To: "'Fast Track Technologies'" <fast_track at vsnl.com>;
> > <cisco-nsp at puck.nether.net> Sent: Thursday, March 25, 2004 1:49 AM
> > Subject: RE: [nsp] Maximum 2 MBPs Serial Ports in the 2610
> >
> >
> > cisco-nsp-bounces at puck.nether.net wrote:
> >> Hi,
> >
> > Hello.
> >
> >>
> >> Can I get (6) 2MBPs Serial Ports in the CISCO 2610 (not the 2610XM) -
> >
> > That would have been very easy if the 2600 supported the NM-4T
> > network module. You'd have the 2x WIC-1T in the integrated slot, and
> > add the NM-4T in the other slot. Unfortunately, the 2600 doesn't
> > support the NM-4T. It will only run on 3620, 3640, 3660, 2691, 3725
> > and 3745.
> >
> >> say, (2) WIC-2Ts and (1) NM-2W with either (2) WIC-1Ts or (1) WIC-2T?
> >
> > What you could is have 4 smart serial interfaces in your integrated
> > slot, two for each WIC port. You can then install an NM-2FE2W into
> > slot1, and have 2x NM-WIC-1T in there.
> >
> >>
> >> Thanks
> >> Sunil
> >
> > However, why are you looking at the 2610? It only has one Ethernet
> > port, running at only 10Mbps? Unless the router is going to be an
> > access aggregator feeding into a larger router?
> >
> >>
> >> _______________________________________________
> >> cisco-nsp mailing list  cisco-nsp at puck.nether.net
> >> https://puck.nether.net/mailman/listinfo/cisco-nsp archive at
> >> http://puck.nether.net/pipermail/cisco-nsp/
> >
> > Regards,
> >
> > Mark Tinka
> > Technical Manager, Africa Online Swaziland
>
> Regards,
>
> Mark Tinka
> Technical Manager, Africa Online Swaziland
>