[c-nsp] Dot1q subinterfaces on cisco 1721
Sorin CONSTANTINESCU
consta at gmail.com
Tue Oct 12 00:04:17 EDT 2004
Hi, Rodney!
Please take a look at the log below:
=== cut here ===
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int f0.1
Router(config-subif)#do sh ver | incl 1721|IOS
IOS (tm) C1700 Software (C1700-IPBASE-M), Version 12.3(5), RELEASE
SOFTWARE (fc1)
cisco 1721 (MPC860P) processor (revision 0x200) with 55694K/9842K
bytes of memory.
Router(config-subif)#int fas 0
Router(config-if)#int fas 0.1
Router(config-subif)#encap
% Incomplete command.
Router(config-subif)#encap
Router(config-subif)#encapsulation ?
% Unrecognized command
Router(config-subif)#encapsulation
% Incomplete command.
Router(config-subif)#do sh run int fas 0.1
Building configuration...
Current configuration : 33 bytes
!
interface FastEthernet0.1
end
Router(config-subif)#do sh diag
Slot 0:
C1721 1FE Mainboard Port adapter, 1 port
Port adapter is analyzed
Port adapter insertion time unknown
EEPROM contents at hardware discovery:
Hardware Revision : 2.0
PCB Serial Number : FOC072213XW
Part Number : 73-7546-02
Board Revision : A0
Fab Version : 04
Product (FRU) Number : CISCO1721
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF 40 03 5A 41 02 00 C1 8B 46 4F 43 30 37 32
0x10: 32 31 33 58 57 82 49 1D 7A 02 42 41 30 02 04 FF
0x20: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x30: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x40: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
Router(config-subif)#
=== and here ===
Regards,
On Mon, 11 Oct 2004 12:51:22 -0400, Rodney Dunn <rodunn at cisco.com> wrote:
> Please provide more information so someone can help
> if they are willing...
>
> ie:
>
> version of code
> sh diag for platform information
> TAC case # if you have one for reference
>
> I just tried one in the lab:
>
> Router(config-subif)#do sh ver | incl 1721|IOS
> Cisco IOS Software, C1700 Software (C1700-ADVIPSERVICESK9-M), Version 12.3(8)T3, RELEASE SOFTWARE (fc1)
> Cisco 1721 (MPC860P) processor (revision 0x300) with 116726K/14346K bytes of memory.
> Router(config-subif)#int fas 0
> Router(config-if)#int fas 0.1
> Router(config-subif)#encap
> Router(config-subif)#encapsulation do
> Router(config-subif)#encapsulation dot1Q
> % Incomplete command.
>
> Router(config-subif)#encapsulation dot1Q 10
> Router(config-subif)#do sh run int fas 0.1
> Building configuration...
>
> Current configuration : 57 bytes
> !
> interface FastEthernet0.1
> encapsulation dot1Q 10
> end
>
> Router(config-subif)#do sh diag
> Slot 0:
> C1721 1FE Mainboard Port adapter, 6 ports
> Port adapter is analyzed
> Port adapter insertion time unknown
> EEPROM contents at hardware discovery:
> Hardware Revision : 3.0
> PCB Serial Number : FOC0812020D
> Part Number : 73-7546-03
> Board Revision : B0
> Fab Version : 04
> Product (FRU) Number : CISCO1721
> EEPROM format version 4
> EEPROM contents (hex):
> 0x00: 04 FF 40 03 5A 41 03 00 C1 8B 46 4F 43 30 38 31
> 0x10: 32 30 32 30 44 82 49 1D 7A 03 42 42 30 02 04 FF
> 0x20: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
> 0x30: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
> 0x40: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
> 0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
> 0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
> 0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
>
> WIC/VIC Slot 0:
> 4 Port FE Switch
> Daughter card-Version 4 TLV Cookie Format
> Hardware Revision : 1.0
> Part Number : 73-8958-01
> Board Revision : B0
> Deviation Number : 0-0
> Fab Version : 01
> PCB Serial Number : FOC07411GA1
> RMA Test History : 00
> RMA Number : 0-0-0-0
> RMA History : 00
> Top Assy. Part Number : 800-24817-01
> Connector Type : 01
> Base MAC Address : 000d.edd0.bc28
> MAC Address block size : 20
> Product (FRU) Number : WIC-4ESW
> CLEI Code : IPMED00BRA
>
> WIC/VIC Slot 1:
> BRI U - 2091
> Hardware revision 4.0 Board revision B0
> Serial number 0011344887 Part number 800-01834-02
> FRU Part Number WIC-1B-U=
>
> Test history 0x00 RMA number 00-00-00
> Connector type WAN Module
> EEPROM format version 1
> EEPROM contents (hex):
> 0x20: 01 09 04 00 00 AD 1B F7 50 07 2A 02 00 00 00 00
> 0x30: 58 00 00 00 98 12 10 01 FF FF FF FF FF FF FF FF
>
>
> Rodney
>
>
>
>
> On Mon, Oct 11, 2004 at 10:49:32AM -0500, Patrick Bohannon wrote:
> > Hello,
> >
> > I ran into the same problem with several "brand new" 1721s from authorized
> > vendors, and finally just stumbled upon several more 1721s that actually
> > worked correctly. I had a TAC case open for awhile and Cisco finally
> > indicated they believed this to be a hardware problem. It didn't seem to be
> > IOS dependent at all as we tried a multitude of different IOS versions.
> > Their recommendation was to either let Cisco take the router back via
> > SMARTnet for exchange or to return it through your vendor.
> >
> > Very frustrating, I know. If you'll notice, you can type encapsulation and
> > hit enter, and you'll get yelled at for not providing a complete command.
> > However, if you type encapsulation ?, you'll get an invalid command.
> >
> > Good luck!
> >
> >
> >
> > -----Original Message-----
> > From: cisco-nsp-bounces at puck.nether.net
> > [mailto:cisco-nsp-bounces at puck.nether.net] On Behalf Of Sorin CONSTANTINESCU
> > Sent: Monday, October 11, 2004 10:28 AM
> > To: cisco-nsp at puck.nether.net
> > Subject: [c-nsp] Dot1q subinterfaces on cisco 1721
> >
> > Hi,
> >
> > I have a cisco 1721 that doesn't let me set the encapsulation for
> > fastethernet subinterfaces. I tried several IOS images using Feature
> > Navigator, but no results.
> >
> > I took the image running on another 1721, loaded it into the one with the
> > problem, but it still didn't work.
> >
> > === cut here ===
> > Router#conf t
> > Enter configuration commands, one per line. End with CNTL/Z.
> > Router(config)#int f0.1
> > Router(config-subif)#enc?
> > encapsulation
> >
> > Router(config-subif)#enc dot1q 1
> > ^
> > % Invalid input detected at '^' marker.
> >
> > Router(config-subif)#end
> > Router#
> > === and here ===
> >
> > The only difference between the 2 routers is in the output of show ver:
> >
> > The one that works: MPC860P processor: part number 5, mask 2 The one that
> > doesn't work: MPC860P processor: part number 0, mask 32
> >
> > I searched on google, but i didn't find anything. I asked the output
> > interpreter, but still nothing :)
> >
> > Any ideeas?
> >
> > TIA!
> > --
> > Sorin CONSTANTINESCU
> > consta at gmail.com
> > Linux Registered User #222086
> > _______________________________________________
> > cisco-nsp mailing list cisco-nsp at puck.nether.net
> > https://puck.nether.net/mailman/listinfo/cisco-nsp
> > archive at http://puck.nether.net/pipermail/cisco-nsp/
> >
> >
> > _______________________________________________
>
>
> > cisco-nsp mailing list cisco-nsp at puck.nether.net
> > https://puck.nether.net/mailman/listinfo/cisco-nsp
> > archive at http://puck.nether.net/pipermail/cisco-nsp/
>
--
Sorin CONSTANTINESCU
consta at gmail.com
Linux Registered User #222086
More information about the cisco-nsp
mailing list