[c-nsp] Re: GSR E2 LC microcode bundle

[Sorin CONSTANTINESCU]

On 12/19/05, Sorin CONSTANTINESCU <consta at gmail.com> wrote:
> Hi, all.
>
> I have a Cisco 12008 router running 12.0(30)S4 with 1 x
> 4OC12/POS-IR-SC-B (E2), and 1 x 3GE-GBIC-SC (E2). This router is part
> of our MPLS network. The ingress interface is one of the STM-4
> interfaces, and the egress (from this PE router) is a dot1q subif on
> one of the GIGE ports.
>
> When pushing traffic out the GIGE subif, the next router (P) makes a
> lookup in the default routing table, instead of using the VRF
> routing-table. This is very odd, since "show ip cef vrf CustA 1.2.3.4"
> shows 2 labels imposed.
>
> However, traffic from the GRP (traceroute/ping inside the CustA vrf)
> is correctly label-switched.
>
> The microcode bundle loaded is BUNDLE_pos_vanilla which should have
> support for MPLS VPN:
>
> === cut here ===
> LC-Slot2>show controller psa bundle-manager bundle 0
> -- Microcode bundle: -------------------------
> BUNDLE_pos_vanilla
> -- This bundle supports: ---------------------
>   Basic IP                          Configured
>   Basic MPLS                        Configured
>   IPv6 throttling                   Configured
>   Multicast throttling              Configured
>   MPLS VPN                          Configured
>   CsC
>   Sampled Netflow
>   MPLS Aware Sampled Netflow
>   Per Packet Loadbalancing
>   L2TPv3
> LC-Slot2>
> === and here ===
>
> When using "rate-limit input" on the POS interface, the router changes
> the bundle on the ASIC to POS: PIRC:
>
> === cut here ===
> SLOT 2:Dec 19 15:26:40: %LC-6-PSA_UNLOAD_UCODE: Unloading
> (BUNDLE_pos_vanilla) bundle from the PSA
> SLOT 2:Dec 19 15:26:40: %LC-6-PSA_LOAD_UCODE: Loading (POS: PIRC)
> bundle into the PSA
> SLOT 2:Dec 19 15:26:40: %LC-6-PSA_UCODE_NO_SUPPORT: Current bundle
> does NOT support (IPv6 throttling)
> SLOT 2:Dec 19 15:26:40: %LC-6-PSA_UCODE_NO_SUPPORT: Current bundle
> does NOT support (Multicast throttling)
> SLOT 2:Dec 19 15:26:40: %LC-6-PSA_UCODE_NO_SUPPORT: Current bundle
> does NOT support (MPLS VPN)
> === and here ===
>
> this bundle doesn't have support for MPLS VPN, and switches the
> packets on the LC CPU.
>
> === cut here ===
> LC-Slot2>show controller psa bundle-manager bundle 2
> -- Microcode bundle: -------------------------
> POS: PIRC
> -- This bundle supports: ---------------------
>   Basic IP                          Configured
>   Basic MPLS                        Configured
>   Multicast
>   CoS Transparency
>   PIRC                              Configured
> LC-Slot2>
> === and here ===
>
> While doing this helps achieving the goal of the setup, i have a
> problem with the CPU on this linecard getting loaded.


Hi,

The workaround was to configure an INPUT ACL on an any interface on this card.

=== cut here ===
SLOT 2:Dec 21 16:31:55: %LC-6-PSA_UNLOAD_UCODE: Unloading
(BUNDLE_pos_vanilla) bundle from the PSA
SLOT 2:Dec 21 16:31:55: %LC-6-PSA_LOAD_UCODE: Loading (POS: 128 Input
ACL) bundle into the PSA
SLOT 2:Dec 21 16:31:55: %LC-6-PSA_UCODE_NO_SUPPORT: Current bundle
does NOT support (IPv6 throttling)
SLOT 2:Dec 21 16:31:55: %LC-6-PSA_UCODE_NO_SUPPORT: Current bundle
does NOT support (Multicast throttling)
=== and here ===

>
> Any hints?
>
> TIA
> --
> Sorin CONSTANTINESCU
> JNCIS-M, CCNP
> consta at gmail.com
>

Regards,
--
Sorin CONSTANTINESCU
JNCIS-M, CCNP
consta at gmail.com