[c-nsp] 2811 router doesn't recognize T-1 WICs?

[Tim Jackson]

I've got 2x WIC-1DSU-T1-V2 cards in our 3845. Here's a sho diag:

        WIC Slot 0:
        FT1 PMC4351
        Hardware Revision        : 1.0
        PCB Serial Number        : FOC07311ACY
        Part Number              : 73-8346-03
        Board Revision           : A0
        RMA Test History         : 00
        RMA Number               : 0-0-0-0
        RMA History              : 00
        Deviation Number         : 0-0
        Product (FRU) Number     : WIC-1DSU-T1-V2
        Top Assy. Part Number    : 800-22193-01
        CLEI Code                : IP4I380GAA
        EEPROM format version 4

We bought these cards somewhere on ebay for quite cheap after we found out the old WIC-1DSU-T1 cards wouldn't work in our 3845. 

-Tim

-----Original Message-----
From:	cisco-nsp-bounces at puck.nether.net on behalf of Steven Bertsch
Sent:	Tue 1/25/2005 10:00 AM
To:	Jay Hennigan; cisco-nsp at puck.nether.net
Cc:	
Subject:	Re: [c-nsp] 2811 router doesn't recognize T-1 WICs?

Jay,

I'm in the same boat.   Cisco no longer supports WIC-1DSU-T1, but
supposedly supports the WIC-1DSU-T1-V2 card in the 2821, but I
have been unable to get any to work.

I decided to go with a multiflex card instead which shows up just
fine.    In my case, a VWIC-2MFT-T1-DI, which can terminate two
T1 channel-groups with add/drop support.

A VWIC-1MFT-T1 should work fine as a replacement for a WIC-1DSU-T1-V2
for most applications.

At 07:17 PM 1/24/2005, Jay Hennigan wrote:
>Hello fellow Cisco-NSP folk.
>
>I have a brand new 2811 router which according to the Cisco DPRG
>configurator is supposed to take the WIC-1DSU-T1-V2 modular WICs
>as opposed to the non-V2 type.
>
>So we paid the higher price for brand-spanking-new V2 modules, and they
>don't show up.  "sho diag" gives:
>
>         WIC Slot 0:
>         Unknown WAN daughter card
>         WIC module not supported/disabled in this slot
>         Hardware revision 64.0          Board revision >1
>         Serial number     1379991808    Part number    800-7441222-79
>         Test history      0x43          RMA number     48-55-51
>         Connector type    PCI
>         EEPROM format version 1
>         EEPROM contents (hex):
>           0x20: 01 80 40 00 52 41 01 00 C1 8B 46 4F 43 30 37 33
>           0x30: 31 31 41 36 4A 82 49 20 9A 03 42 41 30 03 00 81
>
>Tried two different WICs in all slots with similar results.
>
>Is there some magic needed to get these recognized or do I have a hardware
>issue?  The box is running IP-Base 12.3(11)T2, same results with 12.3(8)T.
>
>--
>Jay Hennigan - CCIE #7880 - Network Administration - jay at west.net
>WestNet:  Connecting you to the planet.  805 884-6323      WB6RDV
>NetLojix Communications, Inc.  -  http://www.netlojix.com/
>_______________________________________________
>cisco-nsp mailing list  cisco-nsp at puck.nether.net
>https://puck.nether.net/mailman/listinfo/cisco-nsp
>archive at http://puck.nether.net/pipermail/cisco-nsp/

Regards,
_______________________________________________________________
Steven Bertsch, System Administrator    Infinity AccessNET
sbertsch at iaxs.net                       Voice 952/944-7123 x161
http://www.iaxs.net/                    Fax   952/944-0115
_______________________________________________________________
Your Business Internet Service Provider

_______________________________________________
cisco-nsp mailing list  cisco-nsp at puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-nsp
archive at http://puck.nether.net/pipermail/cisco-nsp/