[c-nsp] 7600 switchover

Kim Onnel karim.adel at gmail.com
Sun Sep 4 10:56:01 EDT 2005 

Hi,

I am running a 7609 with the following modules:

Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ 
-----------
3 0 2 port adapter FlexWAN WS-X6182-2PA JAB081508NX
4 0 2 port adapter FlexWAN WS-X6182-2PA JAB081508QU
5 2 Supervisor Engine 720 (Active) WS-SUP720-BASE SAD081408YM
6 2 Supervisor Engine 720 (Cold) WS-SUP720-BASE SAD081502HK

Mod MAC addresses Hw Fw Sw Status
--- ---------------------------------- ------ ------------ ------------ 
-------
3 000f.3416.5d10 to 000f.3416.5d4f 1.6 12.2(18)SXD 12.2(18)SXD Ok
4 000f.f704.a4a0 to 000f.f704.a4df 1.6 12.2(18)SXD 12.2(18)SXD Ok
5 000d.bda3.e9bc to 000d.bda3.e9bf 3.1 7.7(1) 12.2(18)SXD Ok
6 000d.2910.4b08 to 000d.2910.4b0b 3.1 7.7(1) 12.2(14)SX1 Ok

Mod Sub-Module Model Serial Hw Status
--- --------------------------- ------------------ ------------ ------- 
-------
5 Policy Feature Card 3 WS-F6K-PFC3A SAD081407SY 2.2 Ok
5 MSFC3 Daughterboard WS-SUP720 SAD081503XR 2.2 Ok
6 Policy Feature Card 3 WS-F6K-PFC3A SAD0815053L 2.2 Ok
6 MSFC3 Daughterboard WS-SUP720 SAD0815049W 2.2 Ok

Mod Online Diag Status
--- -------------------
3 Pass
4 Pass
5 Pass
6 Pass


If i understand correctly, Hot standby is when full redundancy between 2 
modules(Supervisor) is achieved, redundancy for processing and traffic, but 
the cold standby is when its not full redundant and it happens when state 
information is not sent from Active to cold for some reason ?

My active Sup720 is in module 5, because of some power problem this morning, 
it switched to module 6, as you can see from the log below, all BGP peers 
went down, and module 6 took place

I asked TAC if i can use the port on the standby module and they confirmed, 
so i put an Internet link on the Giga6/1 interface on the standby sup, with 
a BGP peer up, could that break the redundancy rule ? meaning, if i use the 
port on the standby and switching between modules takes place, should the 
gig on the standby be still working ?

When it switched active from 5 to 6, some ports on the flexwans didnt work 
and the Gig6/1 too

Below are the logs:

Log Buffer (8192 bytes):

UN-SP-STDBY-6-ACTIVE: Initializing as ACTIVE processor
7w2d: %SPANTREE-SP-5-EXTENDED_SYSID: Extended SysId enabled for type vlan
7w2d: SP: SP: Currently running ROMMON from S (Gold) region
7w2d: %SYS-SP-5-RESTART: System restarted --
Cisco Internetwork Operating System Software
IOS (tm) s72033_sp Software (s72033_sp-SPV-M), Version 12.2(14)SX1, EARLY 
DEPLOYMENT RELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 1986-2003 by cisco Systems, Inc.
Compiled Tue 27-May-03 19:32 by ccai

*Sep 4 08:05:00: %OIR-SP-6-INSPS: Power supply inserted in slot 1
*Sep 4 08:05:00: %C6KPWR-SP-4-PSOK: power supply 1 turned on.
*Sep 4 08:05:00: %OIR-SP-6-INSPS: Power supply inserted in slot 2
*Sep 4 08:05:00: %C6KPWR-SP-4-PSOK: power supply 2 turned on.
*Sep 4 08:05:00: %C6KPWR-SP-4-PSREDUNDANTBOTHSUPPLY: in power-redundancy 
mode, system is operating on both power supplies.
*Sep 4 11:05:03: %MLS_RATE-4-OVERWRITING_VALUE: Overwriting the rate value 
for: VACL LOG casecalling scp_getver_req, len = 242

*Sep 4 11:05:04: %OIR-6-REMCARD: Card removed from slot 3, interfaces 
disabled
*Sep 4 11:05:04: %OIR-6-REMCARD: Card removed from slot 3, interfaces 
disabled
*Sep 4 11:05:04: %OIR-6-REMCARD: Card removed from slot 4, interfaces 
disabled
*Sep 4 11:05:04: %OIR-6-REMCARD: Card removed from slot 4, interfaces 
disabled
*Sep 4 08:05:03: %FABRIC-SP-5-FABRIC_MODULE_ACTIVE: the switching fabric 
module in slot 6 became active
*Sep 4 11:05:04: %OIR-SP-6-INSCARD: Card inserted in slot 6, interfaces are 
now online
*Sep 4 11:05:33: %DIAG-SP-6-RUN_MINIMUM: Module 3: Running Minimum 
Diagnostics...
*Sep 4 11:05:33: %DIAG-SP-6-DIAG_OK: Module 3: Passed Online Diagnostics
*Sep 4 11:05:33: %DIAG-SP-6-RUN_MINIMUM: Module 4: Running Minimum 
Diagnostics...
*Sep 4 11:05:33: %DIAG-SP-6-DIAG_OK: Module 4: Passed Online Diagnostics
*Sep 4 11:05:33: %OIR-SP-6-INSCARD: Card inserted in slot 3, interfaces are 
now online
*Sep 4 11:05:34: %OIR-SP-6-INSCARD: Card inserted in slot 4, interfaces are 
now online
Sep 4 11:05:35: %SONET-4-ALARM: POS3/1/0: B2 BER exceeds threshold, TC alarm 
declared
Sep 4 11:05:35: %SONET-4-ALARM: POS3/1/0: B3 BER exceeds threshold, TC alarm 
declared
Sep 4 11:05:36: %SONET-4-ALARM: POS4/0/0: B2 BER exceeds threshold, TC alarm 
declared
Sep 4 11:05:36: %SONET-4-ALARM: POS4/0/0: B3 BER exceeds threshold, TC alarm 
declared
Sep 4 11:05:38: %BGP-5-ADJCHANGE: neighbor xx.77.0.109 Up
Sep 4 11:05:43: %BGP-3-NOTIFICATION: received from neighbor xx.216.142.5 6/5 
(cease) 0 bytes
Sep 4 11:05:44: %BGP-5-ADJCHANGE: neighbor xx.77.0.129 Up
Sep 4 11:05:45: %SONET-4-ALARM: POS3/1/0: B2 BER below threshold, TC alarm 
cleared
Sep 4 11:05:45: %SONET-4-ALARM: POS3/1/0: B3 BER below threshold, TC alarm 
cleared
Sep 4 11:05:46: %SONET-4-ALARM: POS4/0/0: B2 BER below threshold, TC alarm 
cleared
Sep 4 11:05:46: %SONET-4-ALARM: POS4/0/0: B3 BER below threshold, TC alarm 
cleared
Sep 4 11:05:48: %BGP-5-ADJCHANGE: neighbor xx.216.133.1 Up Active SP has 
(458752/65536K) memory, Standby SP (458720/65536K).
Active RP has (458752/65536K) memory, Standby RP (458720/65536K).

Sep 4 11:06:19: %PFREDUN-SP-4-VERSION_MISMATCH: Defaulting to RPR mode 
(Different software versions)
Sep 4 11:06:20: %BGP-5-ADJCHANGE: neighbor xx.216.142.5 Up 
7w2d: SP:
Cisco Internetwork Operating System Software
IOS (tm) s72033_sp Software (s72033_sp-SPV-M), Version 12.2(14)SX1, EARLY 
DEPLOYMENT RELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 1986-2003 by cisco Systems, Inc.
Compiled Tue 27-May-03 19:32 by ccai
Cisco Internetwork Operating System Software
IOS (tm) s72033_sp Software (s72033_sp-PSV-M), Version 12.2(18)SXD, RELEASE 
SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2004 by cisco Systems, Inc.
Compiled Wed 28-Jul-04 22:40 by cmong


Sep 4 11:06:20: %PFREDUN-SP-6-ACTIVE: Standby initializing for RPR mode
Sep 4 11:06:21: %PFINIT-SP-5-CONFIG_SYNC: Sync'ing the startup configuration 
to the standby Router
Sep 4 11:06:25: %FABRIC-SP-5-FABRIC_MODULE_BACKUP: the switching fabric 
module in slot 5 became standby
Sep 4 11:06:26: %DIAG-SP-6-RUN_MINIMUM: Module 5: Running Minimum 
Diagnostics...
Sep 4 11:06:26: %CHKPT-4-INVALID: Invalid checkpoint client ID on (Active).
Sep 4 11:06:26: %CHKPT-4-INVALID: Invalid checkpoint client ID on (Active).
Sep 4 11:06:26: %CHKPT-4-INVALID: Invalid checkpoint client ID on (Active).
Sep 4 11:06:26: %CHKPT-4-INVALID: Invalid checkpoint client ID on (Active).
Sep 4 11:06:26: %CHKPT-4-INVALID: Invalid checkpoint client ID on (Active).
Sep 4 11:06:26: %CHKPT-4-INVALID: Invalid checkpoint client ID on (Active).
Sep 4 11:06:26: %CHKPT-4-INVALID: Invalid checkpoint client ID on (Active).
Sep 4 11:06:26: %CHKPT-4-INVALID: Invalid checkpoint client ID on (Active).
Sep 4 11:06:26: %CHKPT-4-INVALID: Invalid checkpoint client ID on (Active).
Sep 4 11:06:26: %CHKPT-4-INVALID: Invalid checkpoint client ID on (Active).
Sep 4 11:06:26: %CHKPT-SP-4-INVALID: Invalid checkpoint client ID on 
(Active).
Sep 4 11:06:26: %CHKPT-SP-4-INVALID: Invalid checkpoint client ID on 
(Active).
Sep 4 11:06:26: %CHKPT-SP-4-INVALID: Invalid checkpoint client ID on 
(Active).
Sep 4 11:06:26: %CHKPT-SP-4-INVALID: Invalid checkpoint client ID on 
(Active).
Sep 4 11:06:28: %DIAG-SP-6-DIAG_OK: Module 5: Passed Online Diagnostics
Sep 4 11:06:28: %OIR-SP-6-INSCARD: Card inserted in slot 5, interfaces are 
now online
Sep 4 11:06:38: %BGP-5-ADJCHANGE: neighbor xx.212.255.34 Up
Sep 4 11:07:04: %OSPF-5-ADJCHG: Process 1, Nbr xx.240.110.85 on 
GigabitEthernet5/1 from LOADING to FULL, Loading Done
Sep 4 11:11:14 gw-87 80: Sep 4 11:07:29: %BGP-5-ADJCHANGE: neighbor 
xx.129.254.129 Up 
Sep 4 11:11:23 gw-87 81: Sep 4 11:07:39: %BGP-5-ADJCHANGE: neighbor 
xx.240.110.78 Up 
Sep 4 11:11:32 gw-87 83: Sep 4 11:07:45: %BGP-5-ADJCHANGE: neighbor 
xx.240.110.85 Up 
Sep 4 11:11:35 gw-87 84: Sep 4 11:07:50: %BGP-5-ADJCHANGE: neighbor 
xx.240.110.84 Up 
Sep 4 11:11:37 gw-87 85: Sep 4 11:07:53: %BGP-5-ADJCHANGE: neighbor 
196.204.120.96 <http://196.204.120.96> Up 
Sep 4 11:11:41 gw-87 86: Sep 4 11:07:57: %SNMP-5-COLDSTART: SNMP agent on 
host 7600 is undergoing a cold start
Sep 4 11:12:31 gw-87 88: Sep 4 11:08:48: %REDUNDANCY-3-IPC: cannot open 
standby port no such port
Sep 4 11:13:18 gw-87 90: Sep 4 11:09:34: %BGP-5-ADJCHANGE: neighbor 
172.16.113.120 <http://172.16.113.120> Up 
Sep 4 11:16:46 gw-87 94: Sep 4 11:13:03: %REDUNDANCY-3-IPC: cannot open 
standby port no such port
Sep 4 11:17:20 gw-87 96: Sep 4 11:13:37: %REDUNDANCY-3-IPC: cannot open 
standby port no such port
Sep 4 11:17:25 gw-87 97: Sep 4 11:13:42: %REDUNDANCY-3-IPC: cannot open 
standby port no such port
Sep 4 11:17:49 gw-87 99: Sep 4 11:14:05: %REDUNDANCY-3-IPC: cannot open 
standby port no such port
Sep 4 11:17:49 gw-87 100: Sep 4 11:14:06: %REDUNDANCY-3-IPC: cannot open 
standby port no such port
Sep 4 11:21:56 gw-87 106: Sep 4 11:18:12: %REDUNDANCY-3-IPC: cannot open 
standby port no such port
Sep 4 11:24:33 gw-87 109: Sep 4 11:20:50: %REDUNDANCY-3-IPC: cannot open 
standby port no such port
Sep 4 11:27:26 gw-87 112: Sep 4 11:24:12: %REDUNDANCY-3-IPC: cannot open 
standby port no such port
Sep 4 11:37:06 gw-87 121: Sep 4 11:33:52: %REDUNDANCY-3-IPC: cannot open 
standby port no such port
Sep 4 11:43:01 gw-87 127: Sep 4 11:39:47: %REDUNDANCY-3-IPC: cannot open 
standby port no such port
Sep 4 11:43:26 gw-87 128: Sep 4 11:40:12: %REDUNDANCY-3-IPC: cannot open 
standby port no such port
Sep 4 11:48:25 gw-87 134: Sep 4 11:45:11: %REDUNDANCY-3-IPC: cannot open 
standby port no such port
Sep 4 11:52:15 gw-87 137: Sep 4 11:49:01: %REDUNDANCY-3-IPC: cannot open 
standby port no such port
Sep 4 11:53:39 gw-87 138: Sep 4 11:50:25: %BGP-5-ADJCHANGE: neighbor 
xx.77.0.109 Down Interface flap
Sep 4 11:59:01 gw-87 141: Sep 4 11:55:47: %REDUNDANCY-3-IPC: cannot open 
standby port no such port
Sep 4 12:47:00 gw-87 145: Sep 4 12:43:46: %REDUNDANCY-3-IPC: cannot open 
standby port no such port
Sep 4 12:48:39 gw-87 146: Sep 4 12:45:25: %REDUNDANCY-3-IPC: cannot open 
standby port no such port
Sep 4 13:15:59 gw-87 151: Sep 4 13:12:45: %REDUNDANCY-3-IPC: cannot open 
standby port no such port
Sep 4 13:28:09 gw-87 152: Sep 4 13:24:55: %BGP-5-ADJCHANGE: neighbor 
xx.216.133.1 Down Admin. shutdown
Sep 4 13:28:09 gw-87 153: Sep 4 13:24:55: %BGP-5-ADJCHANGE: neighbor 
xx.216.142.5 Down Admin. shutdown
Sep 4 13:28:09 gw-87 154: Sep 4 13:24:55: %BGP-5-ADJCHANGE: neighbor 
xx.77.0.129 Down Admin. shutdown
Sep 4 13:29:23 gw-87 65: Sep 4 13:26:07: %BGP-5-ADJCHANGE: neighbor 
xx.129.254.129 Up 
Sep 4 13:29:25 gw-87 66: Sep 4 13:26:08: %BGP-5-ADJCHANGE: neighbor 
196.204.120.96 <http://196.204.120.96> Up 
Sep 4 13:29:28 gw-87 67: Sep 4 13:26:12: %BGP-5-ADJCHANGE: neighbor 
xx.216.142.5 Up 
Sep 4 13:29:34 gw-87 68: Sep 4 13:26:17: %BGP-5-ADJCHANGE: neighbor 
xx.77.0.129 Up 
Sep 4 13:29:35 gw-87 69: Sep 4 13:26:18: %BGP-5-ADJCHANGE: neighbor 
xx.216.133.1 Up 
Sep 4 13:30:21 gw-87 71: Sep 4 13:26:54: %BGP-5-ADJCHANGE: neighbor 
xx.240.110.78 Up 
Sep 4 13:30:21 gw-87 72: Sep 4 13:27:01: %BGP-5-ADJCHANGE: neighbor 
xx.129.216.253 Up 
Sep 4 13:30:21 gw-87 73: Sep 4 13:27:01: %BGP-5-ADJCHANGE: neighbor 
xx.240.110.84 Up 
Sep 4 13:31:01 gw-87 74: Sep 4 13:27:36: %PFREDUN-SP-4-PHYSMEM_MISMATCH: 
Asymmetrical redundant configuration: Active SP has (458720/65536K) memory, 
Standby has (458752/65536K).
Sep 4 13:31:01 gw-87 75: Sep 4 13:27:36: %PFREDUN-SP-4-PHYSMEM_MISMATCH: 
Asymmetrical redundant configuration: Active RP has (458720/65536K) memory, 
Standby has (458752/65536K).
Sep 4 13:31:01 gw-87 76: Sep 4 13:27:36: %PFREDUN-SP-4-VERSION_MISMATCH: 
Defaulting to RPR mode (Different software versions)
Sep 4 13:31:01 gw-87 77: Sep 4 13:27:37: %PFREDUN-SP-6-ACTIVE: Standby 
initializing for RPR mode
Sep 4 13:31:01 gw-87 78: Sep 4 13:27:38: %HA_CONFIG_SYNC-3-IPC: cannot open 
standby port no such port
Sep 4 13:31:01 gw-87 79: Sep 4 13:27:38: %HA_CONFIG_SYNC-3-IPC: cannot open 
standby port no such port
Sep 4 13:31:01 gw-87 80: Sep 4 13:27:38: %HA_CONFIG_SYNC-3-IPC: cannot open 
standby port no such port
Sep 4 13:31:01 gw-87 81: Sep 4 13:27:38: %HA_CONFIG_SYNC-3-IPC: cannot open 
standby port no such port
Sep 4 13:31:01 gw-87 82: Sep 4 13:27:38: %IPC-3-APP_IPC_FAIL: Open ipc port 
IPC-Apps:Standby failed. IPC Error: no such port (7)
Sep 4 13:31:01 gw-87 83: -Traceback= 4044267C 404426C8 40442A5C 405DDBAC 
405D6850 405D7684
Sep 4 13:31:01 gw-87 84: Sep 4 13:27:38: %SYS-SP-3-LOGGER_FLUSHED: System 
was paused for 00:00:00 to ensure console debugging output.
Sep 4 13:31:01 gw-87 85: 
Sep 4 13:31:03 gw-87 86: Sep 4 13:27:39: %FABRIC-SP-5-FABRIC_MODULE_BACKUP: 
The Switch Fabric Module in slot 6 became standby
Sep 4 13:31:21 gw-87 87: Sep 4 13:27:41: %DIAG-SP-6-RUN_MINIMUM: Module 6: 
Running Minimum Diagnostics...
Sep 4 13:31:21 gw-87 88: Sep 4 13:27:43: %MLS_RATE-4-DISABLING: The Layer2 
Rate Limiters have been disabled.
Sep 4 13:31:21 gw-87 89: Sep 4 13:27:42: %DIAG-SP-6-DIAG_OK: Module 6: 
Passed Online Diagnostics
Sep 4 13:31:21 gw-87 90: Sep 4 13:27:43: %OIR-SP-6-INSCARD: Card inserted in 
slot 6, interfaces are now online
Sep 4 13:31:21 gw-87 91: Sep 4 13:27:49: %PFINIT-SP-5-CONFIG_SYNC: Sync'ing 
the startup configuration to the standby Router
Sep 4 13:31:21 gw-87 92: Sep 4 13:27:49: %PFINIT-SP-1-CONFIG_SYNC_FAIL: 
Sync'ing the startup configuration to the standby Router FAILED
Sep 4 13:31:21 gw-87 93: Sep 4 13:27:49: %PFINIT-SP-1-CONFIG_SYNC_FAIL: 
Sync'ing the private configuration to the standby Router FAILED
Sep 4 13:31:21 gw-87 94: Sep 4 13:27:49: %PFINIT-SP-1-CONFIG_SYNC_FAIL: 
Sync'ing the startup configuration to the standby Router FAILED
Sep 4 13:31:21 gw-87 95: Sep 4 13:27:49: %PFINIT-SP-1-CONFIG_SYNC_FAIL: 
Sync'ing the private configuration to the standby Router FAILED
Sep 4 13:31:21 gw-87 96: Sep 4 13:27:49: %OIR-SP-3-PWRCYCLE: Card in module 
6, is being power-cycled (RF request)
Sep 4 13:31:21 gw-87 97: Sep 4 13:27:49: %PFREDUN-SP-4-BOOTSTRING_INVALID: 
The bootfile slavesup-bootflash: is not present in standby
Sep 4 13:31:22 gw-87 98: Sep 4 13:27:50: %PFREDUN-SP-6-ACTIVE: Standby 
processor removed or reloaded, changing to Simplex mode
Sep 4 13:31:24 gw-87 99: Sep 4 13:28:01: %BGP-5-ADJCHANGE: neighbor 
172.16.113.120 <http://172.16.113.120> Up 
Sep 4 13:31:50 gw-87 101: Sep 4 13:28:33: %EARL_L3_ASIC-SP-3-INTR_WARN: EARL 
L3 ASIC: Non-fatal interrupt Packet Parser block interrupt
Sep 4 13:31:51 gw-87 102: Sep 4 13:28:35: %TAC-4-SERVREF: Warning: Server 
172.31.10.14:0 <http://172.31.10.14:0> is still referenced by server group.
Sep 4 13:32:03 gw-87 103: Sep 4 13:28:46: %MLS_STAT-SP-4-IP_LEN_ERR: MAC/IP 
length inconsistencies
Sep 4 13:32:44 gw-87 105: Sep 4 13:29:27: %PFREDUN-SP-4-PHYSMEM_MISMATCH: 
Asymmetrical redundant configuration: Active SP has (458720/65536K) memory, 
Standby has (458752/65536K).
Sep 4 13:32:44 gw-87 106: Sep 4 13:29:27: %PFREDUN-SP-4-PHYSMEM_MISMATCH: 
Asymmetrical redundant configuration: Active RP has (458720/65536K) memory, 
Standby has (458752/65536K).
Sep 4 13:32:44 gw-87 107: Sep 4 13:29:27: %PFREDUN-SP-4-VERSION_MISMATCH: 
Defaulting to RPR mode (Different software versions)
Sep 4 13:32:44 gw-87 108: Sep 4 13:29:28: %PFREDUN-SP-6-ACTIVE: Standby 
initializing for RPR mode
Sep 4 13:32:45 gw-87 109: Sep 4 13:29:29: %HA_CONFIG_SYNC-3-IPC: cannot open 
standby port no such port
Sep 4 13:32:45 gw-87 110: Sep 4 13:29:29: %HA_CONFIG_SYNC-3-IPC: cannot open 
standby port no such port
Sep 4 13:32:45 gw-87 111: Sep 4 13:29:29: %HA_CONFIG_SYNC-3-IPC: cannot open 
standby port no such port
Sep 4 13:32:45 gw-87 112: Sep 4 13:29:29: %HA_CONFIG_SYNC-3-IPC: cannot open 
standby port no such port
Sep 4 13:32:45 gw-87 113: Sep 4 13:29:29: %SYS-SP-3-LOGGER_FLUSHED: System 
was paused for 00:00:00 to ensure console debugging output.
Sep 4 13:32:45 gw-87 114: 
Sep 4 13:32:45 gw-87 115: Sep 4 13:29:30: %IPC-3-APP_IPC_FAIL: Open ipc port 
IPC-Apps:Standby failed. IPC Error: no such port (7)
Sep 4 13:32:45 gw-87 116: -Traceback= 4044267C 404426C8 40442A5C 405DDBAC 
405D6850 405D7684
Sep 4 13:32:46 gw-87 117: Sep 4 13:29:29: %FABRIC-SP-5-FABRIC_MODULE_BACKUP: 
The Switch Fabric Module in slot 6 became standby
Sep 4 13:32:47 gw-87 118: Sep 4 13:29:30: %DIAG-SP-6-RUN_MINIMUM: Module 6: 
Running Minimum Diagnostics...
Sep 4 13:32:48 gw-87 119: Sep 4 13:29:32: %MLS_RATE-4-DISABLING: The Layer2 
Rate Limiters have been disabled.
Sep 4 13:32:49 gw-87 120: Sep 4 13:29:32: %DIAG-SP-6-DIAG_OK: Module 6: 
Passed Online Diagnostics
Sep 4 13:32:49 gw-87 121: Sep 4 13:29:33: %OIR-SP-6-INSCARD: Card inserted 
in slot 6, interfaces are now online
Sep 4 13:33:00 gw-87 123: Sep 4 13:29:41: %PFINIT-SP-5-CONFIG_SYNC: Sync'ing 
the startup configuration to the standby Router
Sep 4 13:33:33 gw-87 125: Sep 4 13:30:15: %BGP-5-ADJCHANGE: neighbor 
xx.77.0.109 Up 
Sep 4 13:34:59 gw-87 127: Sep 4 13:31:42: %PFINIT-SP-5-CONFIG_SYNC: Sync'ing 
the startup configuration to the standby Router

More information about the cisco-nsp mailing list