[c-nsp] Does this 1721 have a DSL card in it?

Sam Stickland sam_ml at spacething.org
Thu Sep 8 08:21:24 EDT 2005


Hi,

I'm a bit confused as to whether this 1721 has a DSL card in it.

'sh inventory' and 'sh controllers DSL' (output show below), both seem to 
suggest that it does have a DSL controller. But it doesn't actually have 
any configurable ATM interfaces:

   Router(config)#int ATM 0
                     ^
   % Invalid input detected at '^' marker.

   Router(config)#int ATM 1
                     ^
   % Invalid input detected at '^' marker.

Anyone know whats going on? This is currently running 
c1700-bnr2sy7-mz.123-8.XX.bin.

Any clue would be appreciated :)

Sam

'sh inventory' says:

   NAME: "1721 chassis", DESCR: "1721 chassis, Hw Serial#: 486148061, Hw
   Revision: 0x100"
   PID: 1721              , VID: 0x100, SN: FOC07220W3G (486148061)

   NAME: "Chassis Slot", DESCR: "1700 Chassis Slot"
   PID: 1700 Chassis Slot , VID:    , SN:

   NAME: "C1721 Mainboard", DESCR: "C1721 Mainboard"
   PID: C1721 Mainboard   , VID: 0x100, SN: FOC07220W3G (486148061)

   NAME: "Daughter card slot:0", DESCR: "1700 DaughterCard Slot"
   PID: 1700 DaughterCard Slot, VID:    , SN:

   NAME: "WIC/VIC 0", DESCR: "WAN Interface Card - T1E1 or ATM (With 
GSHDSL-F module)"
   PID: WAN Interface Card - T1E1 or ATM (With GSHDSL-F module), VID:    , 
SN: 558756439

   NAME: "Daughter card slot:1", DESCR: "1700 DaughterCard Slot"
   PID: 1700 DaughterCard Slot, VID:    , SN:

   NAME: "WIC/VIC 1", DESCR: "WAN Interface Card - Ethernet"
   PID: WAN Interface Card - Ethernet, VID: 3.0, SN: 3951704543

   NAME: "Ethernet0", DESCR: "PQUICC Ethernet"
   PID: PQUICC Ethernet   , VID:    , SN:

   NAME: "FastEthernet0", DESCR: "PQUICC_FEC"
   PID: PQUICC_FEC        , VID:    , SN:

'sh controllers DSL' reports:

    DSL 0 controller DOWN
   SLOT 0: Globespan xDSL controller chipset
    DSL mode: SHDSL Annex A
    No frame mode configured
    Line Re-activated 0 times after system bootup
    LOSW Defect alarm: ACTIVE
    CRC per second alarm: ACTIVE
    Line termination: CPE
    FPGA Revision: 0xA9

         Current 15 min CRC: 0
         Current 15 min LOSW Defect: 0
         Current 15 min ES: 0
         Current 15 min SES: 0
         Current 15 min UAS: 0

         Previous 15 min CRC: 0
         Previous 15 min LOSW Defect: 0
         Previous 15 min ES: 0
         Previous 15 min SES: 0
         Previous 15 min UAS: 0

    Line-0 status
    Chipset Version:  1
    Firmware Version:  A29733
    Modem Status:  un checked mode, Status F368
    Last Fail Mode:  No Failure status:0x0
    Dying Gasp: Present


'sh ip int br'

   Interface                  IP-Address      OK? Method Status 
Protocol
   Ethernet0                  x.y.z.210    YES NVRAM  up 
up
   FastEthernet0              x.y.z.205    YES NVRAM  up 
up



More information about the cisco-nsp mailing list